|
|
EDA365欢迎您！
您需要 登录 才可以下载或查看，没有帐号？注册
x
我在生成网表后，导入pads layout， 结果报告如下错误：) q4 I1 J' |: Q$ V
Can't find part Type item < XTAL_HC49SMT >
. u* F2 t6 \: b0 K4 {$ l( yY1 XTAL_HC49SMT2 g9 A- G/ A( C! S8 z' p
Can't find part Type item < XTAL_HC49SMT >8 v b; I# x: X, h' B4 q2 |" D* S& P9 M
Y2 XTAL_HC49SMT3 L) c, M7 A# |0 U; _* f
Can't find part Type item < XTAL_HC49SMT >
& r+ i6 M+ }! H' cY3 XTAL_HC49SMT
6 G; L8 c( j; N" W*Part name not found U13* H8 q' ]% X3 U( E: D1 z. c
U13.1 R9.1 C45.2 R13.2 R14.1/ N6 ] g) V+ k% m
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1356420
( a1 X( s: z0 {: Q- y*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal XT2_PHY: z1 t$ c" m. V+ V
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_D+2
" g, K3 o8 e! f) }8 ?*Part name not found Y1/ Y0 H+ @( [) j1 }3 U! N& h+ E
Y1.2 U6.1 C28.1 J3.1 J4.1 J5.1, x8 s& Z2 S3 J' Y5 g
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal OSC1
% d+ j% b" E! k/ U/ j: Q*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal CRS_PHY6 u v* K ]2 f% H; F
*Part name not found Y2
5 Q/ S! i6 ]5 OU5.34 Y2.2 C41.2 U: B; z, o" U) g( J
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal RTCK1
( R9 Q9 ^4 B7 a3 H*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal VDD_PHY! h2 [ e8 T! E4 E; q6 G( z' q
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal TXD1_PHY& H" y% @8 k* L' L
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_OTG_ID
% |9 @- {% X! ~ o除了上述报错元件不能导入，可以导入其它元件。我的部分PCB封装在自己建的pads库里，还用了些常用的自带库。请问
! }* I6 \) w$ x9 u% c: l这些错是什么原因造成的？我看了一天了也没头绪。
2 q q* V, h! w% T6 a6 _6 T多谢各位看完。
: a- D* v6 q% W# h' t7 \我会把整个设计放在附件里。
$ _5 u6 C$ K% I% _; o% s7 T再谢。 |
|
/1 
发表于 2008-9-2 10:28
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
支持！
反对！
楼主
我已经把封装改好了。