|
|
EDA365欢迎您！
您需要 登录 才可以下载或查看，没有帐号？注册
x
我在生成网表后，导入pads layout， 结果报告如下错误：
$ s8 F. A& ~- z' A2 qCan't find part Type item < XTAL_HC49SMT >3 g1 h7 N- U$ {% ~) _* R2 ?
Y1 XTAL_HC49SMT
* Q( o; N& o7 s' h2 D7 T2 SCan't find part Type item < XTAL_HC49SMT >2 p; E. N$ |% G1 `" Q& ^0 J4 q
Y2 XTAL_HC49SMT, }8 ^3 R/ d2 z
Can't find part Type item < XTAL_HC49SMT >) W; W& k. o3 f: E+ E; g
Y3 XTAL_HC49SMT/ x* @5 x0 I0 X! H8 y
*Part name not found U13
+ R3 B: i# \% o9 ~! N3 p) e* CU13.1 R9.1 C45.2 R13.2 R14.18 m! V4 p. V1 _. F3 i$ I8 i9 _: n
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N13564207 c/ }0 S, y6 Z: }
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal XT2_PHY
A5 I" j% }2 g0 T: d4 ?*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_D+2
+ w) w; }" {+ i1 J*Part name not found Y1
, V5 f( u4 p8 {: BY1.2 U6.1 C28.1 J3.1 J4.1 J5.12 C5 Q8 V$ d5 F
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal OSC1
5 n2 ?7 r: I8 v3 X& G8 L# a*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal CRS_PHY
, t7 Y/ _+ {# M5 A*Part name not found Y2- N- [3 |9 E6 A$ ]) t
U5.34 Y2.2 C41.2
$ E% D+ G- E- a* |8 Z X- k*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal RTCK1
* A# V& P w; Q" N6 E*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal VDD_PHY0 m( }( t+ I0 S! e8 _4 E
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal TXD1_PHY G/ y" M2 U b' }: [ w
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_OTG_ID
' h$ c1 ?) t: q" b9 b除了上述报错元件不能导入，可以导入其它元件。我的部分PCB封装在自己建的pads库里，还用了些常用的自带库。请问0 \. j+ I1 c' n+ B* {3 |
这些错是什么原因造成的？我看了一天了也没头绪。' e/ [- H. R& r; D/ _( }
多谢各位看完。. X9 T( C* M% e
我会把整个设计放在附件里。$ X6 z3 p$ {0 V6 H' ^* L0 B/ {
再谢。 |
|
/1 
发表于 2008-9-2 10:28
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
支持！
反对！
楼主
我已经把封装改好了。