Allegro导入第三方网表出错

656504257

本想把PADS Logic的转为ORCAD，下了个E-studio.pro软件安装不了，只好输出网表导入到Allegro，但是出现以下错误，请教高手，怎么解决？
^
ERROR(SPMHNI-63): Invalid keyword, keyword ignored.
-------------------------------------------------------------------------------
^
Execution stopped before reading entire input file.
! t; S2 h/ D. k-------------------------------------------------------------------------------
5 g. ?( k8 T3 d3 A7 z; v. e
===========================================================
End of NETLIST IN Syntax/Logic Check
===========================================================

4 Y$ O9 ^0 N5 S$ i6 A. gTotal Netlist Warnings =  0.
Total Netlist Errors   =  1.

- u2 R, r# m7 g3 j7 q. y& ?# E
0 R9 T. @1 L0 d2 ?: x& [: W===========================================================
5 m3 J* q; s' w- _: p; c2 R
Total Device File Warnings =  0.
Total Device File Errors   =  0.

===========================================================
: F, A3 R8 w. o
Total Combined Netlist and Device File Warnings =  0.
Total Combined Netlist and Device File Errors   =  1.

===========================================================
End of Allegro NETLIST IN Log
===========================================================
) q% N9 `% e+ L; ^" N& P

风吹摇摆

我的也是这样，总是有一个网络出错，在原理图里删除网络重新连后，另外一个网络出错了
; h8 ^% x* Q/ W& x% R求大神解决
! Y9 Z4 L  M% J; C5 f3 @. [，$$$883' ; NSR1.2 NSR2.2 U6.6
^
ERROR(SPMHNI-63): Invalid keyword, keyword ignored.
9 J8 V& K, p( Q9 V5 u9 h-------------------------------------------------------------------------------
^
Execution stopped before reading entire input file.
5 z8 b+ D8 ?; i6 ]-------------------------------------------------------------------------------

===========================================================
4 @6 k4 N$ p8 n1 ~. V( }$ D* l6 fEnd of NETLIST IN Syntax/Logic Check
===========================================================

Total Netlist Warnings =  0.
Total Netlist Errors   =  1.
0 ]7 J+ s6 H# {& r  S5 s

风吹摇摆

查下网表里面有非法字符例如$$$883' ; NSR1.2 NSR2.2 U6.6
6 X" k% J: S! a7 }/ y7 X' }- v; V$ R'$$$1157' ; R438.2 U39.4
, b4 ?' F# M. v* B'$$$1184' ; R435.1 R439.2 U39.6
'$$$1196' ; R252.1 U31.2
/ c( U. E4 a; q( z( {  M! W9 f6 D/ [- ~9 f'$$$1198' ; R253.1 U31.1
'$$$1560' ; R49.1 U11.1
'$$$2732' ; R226.2 R229.2 U31.3
'$$$2826' ; R250.2 R254.2 U31.5
'$$$2903' ; R297.2 R298.2 U31.6
'$$$2954' ; C72.2 L6.1 Q24.5 Q24.6 Q24.7 Q24.8 R49.2
' a4 j2 K- J$ y- ~! h'$$$3044' ; R299.2 U31.7
# H; C$ ^5 b; E# a* j'$$$4685' ; C177.1 C192.1 C196.1 L17.1 L31.1 U18.22
4 `& \/ U; j/ H'$$$4720' ; Q7.1 U11.2
'$$$4813' ; D6.1 L30.2 U9.1
8 c' y* _, Y! d' P'$$$5014' ; D2.2 J1.7 R269.2 R329.2
'$$$5015' ; D16.2 J1.5 R273.2
. ~# L/ Z2 `' T1 g'$$$5016' ; D3.2 J1.3 R276.2 R330.2
, A( u8 D3 w7 D2 b'$$$5017' ; D18.2 J1.2 R285.2 R331.2
9 ~1 Y% S$ }7 A0 ~'$$$5018' ; D20.2 J1.1 R264.2 R332.2
'$$$5019' ; D1.2 J1.8 R286.2 R328.2
  w5 D/ P; V9 b6 }* y'$$$5840' ; R122.1 U18.18
1 S8 _# R2 p9 V9 x& g+ G'$$$5842' ; R123.1 U18.19
: T, u0 `- F$ k'$$$5844' ; R124.1 U18.20
. T) f4 c' ^. d: `% N$ `7 w4 L改过来就可以了

风吹摇摆

刚才说错了，这个要手动修改网表，在含有$$$的网络前面加上“$NETS”例如：
$NETS
+ b. U) f5 F; Q# S6 B2 k'$$$883' ; NSR1.2 NSR2.2 U6.6
5 [' A: l* p( ~'$$$1157' ; R438.2 U39.4
+ A" C% L$ ~3 \8 z, Y! t'$$$1184' ; R435.1 R439.2 U39.6
'$$$1196' ; R252.1 U31.2
'$$$1198' ; R253.1 U31.1

ayalcy

不行啊 ，还是报错
这个要怎么改啊