新手求助

JiBi_Supertramp

请问这几个错误怎么解决，万分感谢：
drc-502 - [schematic: Schematic1, net: GND] Global net name not listed in legal_globals
* O0 }# K. q4 e5 }, u! T* h) R drc-502 - [schematic: Schematic1, net: 14V4_SW] Global net name not listed in legal_globals
! n7 J( p3 c; J- y/ g drc-502 - [schematic: Schematic1, net: 14V4_PERM] Global net name not listed in legal_globals
5 P- G4 ?1 g+ ^4 [" _7 Y* n+ E drc-502 - [schematic: Schematic1, net: 5V_SW] Global net name not listed in legal_globals
5 n$ i5 c7 s! l; d' S# ` drc-502 - [schematic: Schematic1, net: 3V3_SW_GPS] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_SW_GYRO_ACC] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_SW_PHY] Global net name not listed in legal_globals
4 M" J5 w& c) A/ d0 s" y6 f drc-502 - [schematic: Schematic1, net: 5V_SW_GYRO] Global net name not listed in legal_globals
7 s! r0 H2 B, x1 z: }' |8 e( s drc-502 - [schematic: Schematic1, net: uP2HPY_PWR_EN] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 5V_PERM] Global net name not listed in legal_globals
( u, {( x! Y1 A2 S# q$ b0 U$ q, ` drc-502 - [schematic: Schematic1, net: GPS_PERM_BCKP] Global net name not listed in legal_globals
9 d, n6 y3 p' w7 M( a+ ^" V drc-502 - [schematic: Schematic1, net: 3V3_GPS_VCC] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 1V8_SW] Global net name not listed in legal_globals
: x4 v/ K2 T- y1 Z. Z/ v' | drc-502 - [schematic: Schematic1, net: 3V3_GPS_ANT] Global net name not listed in legal_globals
; k6 a- T/ W2 B+ ?5 v6 T drc-502 - [schematic: Schematic1, net: AGND] Global net name not listed in legal_globals
drc-504 - [schematic: Schematic1, net: 14V4_SW] Global Signals '' '14V4_SW' are shorted
drc-504 - [schematic: Schematic1, net: 5V_SW] Global Signals '' '5V_SW' are shorted
9 Q  C6 C2 v$ ?: ?: B  `: U4 c drc-504 - [schematic: Schematic1, net: 3V3_SW_GPS] Global Signals '' '3V3_SW_GPS' are shorted
+ e# V  r0 f9 N' [ drc-504 - [schematic: Schematic1, net: 5V_SW_GYRO] Global Signals '' '5V_SW_GYRO' are shorted
1 ~- J: u6 s4 Y0 } drc-504 - [schematic: Schematic1, net: 1V8_SW] Global Signals '' '1V8_SW' are shorted
+ {8 F3 G. n" q* D/ {. r* @ drc-504 - [schematic: Schematic1, net: 3V3_GPS_ANT] Net '3V3_GPS_ANT' is connected to Global Signal pin 'power_in.1'
4 Y) ^8 ~& x$ @# h  t3 O$ } drc-504 - [schematic: Schematic1, net: 3V3_GPS_ANT] Net '3V3_GPS_ANT' is connected to Global Signal pin 'power_out.1'

- A8 U/ C8 i5 g

ugqy

电源和地的:
9 V0 x7 G" I( o! K4 W1.在Global Signal 里面设置这些信号为全局变量
$ x! N5 f* C& }( k2.原理图里面把这些信号的连接符改为页间连接器。
3.在元件库里面的symbol库里面把这些信号添加为电源、地的标准连接符号。
3 C1 C6 H# Z3 h. E
其他跨页信号的：
$ I8 ?- I  N, S5 k# H  K例如：GPS_PERM_BCKP uP2HPY_PWR_EN 用页间连接器。
* u6 Y% |- M- D+ f; H8 k

Magic520

兄弟，你真强~

lalasa1987

无视掉也不要紧。。。