上传“如何在OrCAD定義Allegro可swap的排阻”

hu311

详见附件文档！

风雨者

为什么会出现子图中的阻排位号不能编号,始终为RN1,导致检查不通过,不能生成网表?
& _0 b2 s+ n$ o, ]
--------------------------------------------------
$ {. k, S/ s8 S7 w; h# k! z! ]- zChecking Schematic: RN22 RN-8P4R-1
--------------------------------------------------
Checking Electrical Rules

. z. j" k) g# {+ _/ ~Checking for Unconnected Nets

Checking Off-Page Connections

; z, z8 v, V5 Y6 \: JChecking Pin to Port Connections
8 Y9 V8 ~; `- u- G  S+ b
Checking for Invalid References
% X, X4 @( ^  ^9 P
Checking for Duplicate References
ERROR [DRC0010]   Duplicate reference RN22/RN1D:  RN-8P4R-1, RN-8P4R  (5.10, 2.50)
ERROR [DRC0010]   Duplicate reference RN22/RN1A:  RN-8P4R-1, RN-8P4R  (5.10, 2.20)
ERROR [DRC0010]   Duplicate reference RN22/RN1B:  RN-8P4R-1, RN-8P4R  (5.10, 2.30)
ERROR [DRC0010]   Duplicate reference RN22/RN1C:  RN-8P4R-1, RN-8P4R  (5.10, 2.40)

许汉洲

风雨者 发表于 2008-10-28 20:22
为什么会出现子图中的阻排位号不能编号,始终为RN1,导致检查不通过,不能生成网表?
  
4 w& E& x. H9 y  B--------------- ...

重复管脚，重复管脚连接在不同网络，建议修改原理图。

hukee

一直都不知道allegro中 swap pin是怎么用的。

lara_bxc

这个是在orcad中建排阻的库吗？

richardz88

very good!

hu311

是在原理图里修改属性。

03155001

正需要，very good

finezhang

very good

lihuizju

谢谢。下来看看

fhjltw

及时雨啊，正需要，谢！

abyass

顶，好东西

lbq211

定一
7 U/ v1 _* Q6 d' ]8 C. t% Q+ g个

风雨者

好方法!讲解很细致!赞一个!

风雨者

可为什么生成网表时出错呢?
) f. Z, M6 I) h7 t# H: i  Check for incorrect packaging of all devices in RN1.
+ v$ Y8 t; o- u#569 Error   [ALG0045] multiple pin 4's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 63.50).
; ~! V& g" ?/ g+ \              Check for incorrect packaging of all devices in RN1.
& n0 k9 m( c( D' E#570 Error   [ALG0045] multiple pin 5's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 63.50).
              Check for incorrect packaging of all devices in RN1.
2 k8 R7 p. K( ]+ _#571 Error   [ALG0045] multiple pin 1's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 55.88).
0 d1 m- g9 f1 D8 g* V              Check for incorrect packaging of all devices in RN1.
#572 Error   [ALG0045] multiple pin 8's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 55.88).
              Check for incorrect packaging of all devices in RN1.
1 F4 {0 M0 W( W% K1 g! ?) }#573 Error   [ALG0045] multiple pin 2's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 58.42).
              Check fo
r incorrect packaging of all devices in RN1.

252631

good,谢谢!