【PIC32 starter kit】之性能初窥

duzy

板载资源介绍
一．正面：
* Z6 v- O& N" ^官方原文指导：
The top assembly of the board includes these key features, as indicated in Figure 1-1:
3 c) Y7 T# R2 L  [6 l6 b1.    PIC32MX795F512L 32-bit microcontroller (U2).   核心的东西
2.    Green power indicator LED (D4).    电源指示灯
3.    On-board crystal for precision microcontroller clocking (8 MHz) (Y1). 板上晶振
0 C1 j1 g  S  \4.    USB connectivity for on-board debugger communications (J7).   小口USB连接器用于DEBUG
5.    Debug indicator LED (D7).                 Debug指示灯
) O1 T6 F: [6 V1 n) H6.    Three push button switches for user-defined inputs (SW1, SW2, SW3). 3个按键，用户输入
7.    Three user-defined indicator LEDs (D1, D2, D3).   3个用户指示灯
8.    USB Type A receptacle connectivity for PIC32 host-based applications (J4). USB连接器用于用户使用
4 j. v# ~& }9 }0 C$ L% d& E9.    HOST mode power jumper (J5).   电源模式跳线
5 o& g9 d6 X, T8 J: c10.  LAN8740A PHY Daughter Board headers (J2)     这个拿到板的人一看就明白,网络连接接口
11.  50 MHz Ethernet PHY oscillator (Y3).  50MHZ晶振 没看文档前还以为是电容   
" N& T& C( n! D/ y/ q2 @, q12.  32 kHz oscillator (optional) (Y2). 32KHZ晶振
13.  USB Host and OTG power supply for powering PIC32 USB applications (U4). 用户使用的USB工作芯片。
二．反面：
& Z. c3 S7 I+ |1. Regulated +3.3V power supply for powering the starter kit through USB or
5 F- f+ r( P) f  ]4 ?; Zexpansion board (U8).   3.3V的电源支撑
2.Connector for various expansion boards (J1).  扩展板连接器
# X: ~8 Q1 T- G( ?1 o1 q" a! T2 d3.USB Type micro-AB receptacle for OTG and USB device connectivity for PIC32
4 c; i7 c+ r2 \2 m& `3 B) A( _OTG/device-based applications (J3).       OTG,micro-USB连接器
4.PIC24FJ256GB106 USB microcontroller for on-board debugging (U6).usb-debug芯片。
5 R, i, e# e" C% z) {+ ?: h基本情况就介绍到这儿，这个板子本身所带的资源及信息。
7 [  Q  J# W1 }: Z' @: [
=======================================================================================================
三．性能及相关参数（捡主要的）
3.1 power supply
. b/ T' U* q1 O! a5 ^•  USB bus power connected to USB debug connector, J7.USB_debug连接器提供
: j$ w3 Z$ ?6 d" M/ N•  An external application board with a regulated DC power supply that provides +5V  J1也就是板子背面最大的那个接扩展板的接口接供，暂不满足。
can be connected to the J1 application board connector that is provided on the bottom side of the board.
3.2 PIC32 USB Connectivity（USB连接）
- v2 |: n. d" B% d, eUSB连接有3种模式，像大家最常用U盘，接到PC上，这种U盘就属于DEVICE MODE，PC就属于HOST MODE这种是大家最常用到的，
( K. |1 W  B& a3 k" K7 d还有一种是OTG模式，
& V( |$ ?/ C, I. a: p•HOST Mode – Connect the device to the Type A connector J4, located on the top side of the starter kit. If using the Debug USB port to power the Host port, install
jumper J5 to short the back-power prevention diode. Note that a maximum of  ~400 mA can be supplied from the Debug USB port to the Host port using this method.
如果想要使用USB主机模式，那么必需就要接到J4上，也就是那个我们最常见的USB口上，如果是用MICRO-USB供电，则需要短接J5,也就是我们
在面板上看到的那两个排针。
' `. v# ~  X  O•DEVICE Mode – Connect the debug mini-B USB cable to port J7 and then connect the starter kit to the host using a cable with a Type-B micro-plug to the starter
4 u2 C6 I  k% y$ G: {kit’s micro-A/B port J3, located on the bottom side of the starter kit. The other end of the cable must have a Type-A plug. Connect it to a USB host. Jumper J5 should
be removed.
1 S! S' L, _5 t8 ^9 s) _( a% W! TDEBUG口，即是设备模式，但是需要将j7,跟J3都连接到电脑，J5也就是那个跳线需要断开。
•OTG Mode – Connect the starter kit to the OTG device using an OTG micro-A/B cable to the micro-A/B port J3, located on the bottom side of the starter kit. The
starter kit provides an on-board power supply capable of providing 120 mA Max. This supply is controlled by the PIC32MX795F512L microcontroller. Jumper J5 should
5 N$ [% t3 Y, }( }) B5 Q$ Hbe removed.
只需要连接J3,但J5跳线要断开。

helendcany

哦，哦，哦，这个要记……

Haiting32451

学习了……