新手求助

JiBi_Supertramp

请问这几个错误怎么解决，万分感谢：
drc-502 - [schematic: Schematic1, net: GND] Global net name not listed in legal_globals
) ^7 t) j8 H( A9 T) P$ E drc-502 - [schematic: Schematic1, net: 14V4_SW] Global net name not listed in legal_globals
! ~, q. b, J2 \$ a5 Z8 i drc-502 - [schematic: Schematic1, net: 14V4_PERM] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 5V_SW] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_SW_GPS] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_SW_GYRO_ACC] Global net name not listed in legal_globals
* d* `9 e2 @$ x  x& d) i$ M" a drc-502 - [schematic: Schematic1, net: 3V3_SW_PHY] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 5V_SW_GYRO] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: uP2HPY_PWR_EN] Global net name not listed in legal_globals
! @3 ]& W& f/ W3 j3 ? drc-502 - [schematic: Schematic1, net: 5V_PERM] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: GPS_PERM_BCKP] Global net name not listed in legal_globals
. n1 O/ N; V3 `: K* v drc-502 - [schematic: Schematic1, net: 3V3_GPS_VCC] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 1V8_SW] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_GPS_ANT] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: AGND] Global net name not listed in legal_globals
8 ~' \) P! F; d( v* s0 S drc-504 - [schematic: Schematic1, net: 14V4_SW] Global Signals '' '14V4_SW' are shorted
& o9 H( t- G0 j: p! ? drc-504 - [schematic: Schematic1, net: 5V_SW] Global Signals '' '5V_SW' are shorted
) B, x/ R3 r$ C. I drc-504 - [schematic: Schematic1, net: 3V3_SW_GPS] Global Signals '' '3V3_SW_GPS' are shorted
) F) F0 ?2 Q" s/ q drc-504 - [schematic: Schematic1, net: 5V_SW_GYRO] Global Signals '' '5V_SW_GYRO' are shorted
( c; S: t& v& D% e# @; `, H' P drc-504 - [schematic: Schematic1, net: 1V8_SW] Global Signals '' '1V8_SW' are shorted
drc-504 - [schematic: Schematic1, net: 3V3_GPS_ANT] Net '3V3_GPS_ANT' is connected to Global Signal pin 'power_in.1'
- M' h& ~* ?" m; R4 F8 W2 Y3 A! H  n drc-504 - [schematic: Schematic1, net: 3V3_GPS_ANT] Net '3V3_GPS_ANT' is connected to Global Signal pin 'power_out.1'

ugqy

电源和地的:
# l4 Y$ M3 O+ O9 d- U9 C1.在Global Signal 里面设置这些信号为全局变量
2.原理图里面把这些信号的连接符改为页间连接器。
3.在元件库里面的symbol库里面把这些信号添加为电源、地的标准连接符号。
  @6 i7 P% `0 [8 d7 Z9 R/ [
/ F) ]! Y- ^7 `+ p+ J其他跨页信号的：
/ }+ p5 R' w1 H% W$ u例如：GPS_PERM_BCKP uP2HPY_PWR_EN 用页间连接器。
0 E  h* \0 @" J2 k6 B7 ?6 u4 r

Magic520

兄弟，你真强~

lalasa1987

无视掉也不要紧。。。