新手求助

JiBi_Supertramp

请问这几个错误怎么解决，万分感谢：
drc-502 - [schematic: Schematic1, net: GND] Global net name not listed in legal_globals
, `$ _7 l" t2 }9 h9 g drc-502 - [schematic: Schematic1, net: 14V4_SW] Global net name not listed in legal_globals
- Y& t1 _* S' V' i$ J drc-502 - [schematic: Schematic1, net: 14V4_PERM] Global net name not listed in legal_globals
) p8 [; Y# e$ Z! { drc-502 - [schematic: Schematic1, net: 5V_SW] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_SW_GPS] Global net name not listed in legal_globals
4 x' {  B/ l. k! ]( t, h drc-502 - [schematic: Schematic1, net: 3V3_SW_GYRO_ACC] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_SW_PHY] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 5V_SW_GYRO] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: uP2HPY_PWR_EN] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 5V_PERM] Global net name not listed in legal_globals
; v0 G( n- T' v3 q drc-502 - [schematic: Schematic1, net: GPS_PERM_BCKP] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 3V3_GPS_VCC] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: 1V8_SW] Global net name not listed in legal_globals
( x- K& \3 t+ B' l drc-502 - [schematic: Schematic1, net: 3V3_GPS_ANT] Global net name not listed in legal_globals
drc-502 - [schematic: Schematic1, net: AGND] Global net name not listed in legal_globals
drc-504 - [schematic: Schematic1, net: 14V4_SW] Global Signals '' '14V4_SW' are shorted
drc-504 - [schematic: Schematic1, net: 5V_SW] Global Signals '' '5V_SW' are shorted
drc-504 - [schematic: Schematic1, net: 3V3_SW_GPS] Global Signals '' '3V3_SW_GPS' are shorted
drc-504 - [schematic: Schematic1, net: 5V_SW_GYRO] Global Signals '' '5V_SW_GYRO' are shorted
drc-504 - [schematic: Schematic1, net: 1V8_SW] Global Signals '' '1V8_SW' are shorted
drc-504 - [schematic: Schematic1, net: 3V3_GPS_ANT] Net '3V3_GPS_ANT' is connected to Global Signal pin 'power_in.1'
drc-504 - [schematic: Schematic1, net: 3V3_GPS_ANT] Net '3V3_GPS_ANT' is connected to Global Signal pin 'power_out.1'
/ Z" b) |9 u: Q8 u0 s
5 ]: f! @2 c  _; X9 M" B

ugqy

电源和地的:
1.在Global Signal 里面设置这些信号为全局变量
2.原理图里面把这些信号的连接符改为页间连接器。
, v* t5 @9 ?. O% ^7 a+ e/ s/ G3.在元件库里面的symbol库里面把这些信号添加为电源、地的标准连接符号。
+ ?  _; U" m; X4 x4 G5 i; a# M" j
5 J" v& _2 p9 o3 D$ \0 @9 _% V其他跨页信号的：
例如：GPS_PERM_BCKP uP2HPY_PWR_EN 用页间连接器。
# f: m+ O$ `" k4 r2 D. U+ o' B

lalasa1987

无视掉也不要紧。。。

Magic520

兄弟，你真强~