|
|
EDA365欢迎您！
您需要 登录 才可以下载或查看，没有帐号？注册
x
本帖最后由 buptdlmuzbx 于 2011-4-20 16:45 编辑
' d' U6 b# x; y* K
, Q# A: }) T1 C2 K/ _6 M9 Y$ \* OSUMMARY:, \1 B3 Z4 q: M& u) ~, g
TOP created with warnings
# [7 _) d) m) x7 d GND created with warnings
: q1 _/ N1 C! s! y# @ VCC created with warnings4 x: g6 h+ X" c1 Q5 n
BOTTOM created.+ j, q$ `+ P# }) c9 h$ f
SILKSCREEN_TOP created with warnings
& i* v; ], x8 l( L% \2 ~( ~ SILKSCREEN_BOTTOM created.$ K/ B" Q/ y" H% I7 y3 `4 Y1 @+ K- x
SOLDERMASK_TOP created.' F, E1 X/ n: Z/ c$ U
SOLDERMASK_BOTTOM created.
2 S3 l- S, P. k# z PASTEMASK_TOP created.4 X$ h+ A) E4 C, J
PASTEMASK_BOTTOM created.
/ q: U0 R$ l4 h s OUTLINE created.& E' L. c# \: K/ b
DRILL created.
: X6 I" } i$ D3 K$ u: b ARTWORK finished+ k4 S3 E8 F* E7 ^& z/ E
这是最后的结果，5 J+ d6 B( a" i; e, C, O; i4 T
我想问下既然光绘finished，那这些warning能忽略吗？. [ v# D% O5 O u
WARNING: 0 width line found at (0.0000 0.6350)
* B, H k5 c# T, r( D ... using undefined line width of 0.1524
- E* m3 Q. R3 u4 n4 MWARNING: Multiple 0 width lines; all will be treated the same as the first.
9 H' Z5 z4 ^1 b# P ... using undefined line width of 0.1524
8 f$ j+ D$ s. d) h- q3 N WARNING: No Photoplot Outline was found,6 g- W+ r* E, Q7 G) X# D
negative shape outline will be determined by Board Outline
% o) `3 S h% u$ A2 p" r WARNING: No Photoplot Outline was found,
+ B* A7 b6 u4 F* @( A# inegative shape outline will be determined by Board Outline4 d, @2 y8 T# j `6 s$ X! `
WARNING: text composed 0 width line found at (9.7282 5.5626): s9 G' R- L6 w) s1 ^9 E1 W8 z
... using undefined line width of 0.1524, u& K8 ~ f: S; {4 q
WARNING: text having Multiple 0 width lines; all will be treated the same as the first.
0 W& @; S0 S3 p( o ... using undefined line width of 0.1524+ H' H. n- C. E# t- [: M
/ K: ?! g7 `" n. M( V! I% L& @; t: o6 r6 L1 t4 }
这是什么呀！谁能给解决下！有木有！有木有！% P5 i! f& ~+ t: S& `$ e
|
|
/1 
发表于 2011-4-20 16:30
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
支持！
反对！
請問您是不是有SHAPE做的零件超出板框了呢？
