PADS元器件换层

xiewu5

pads中元器件换面后怎么不在原来位置啦？

bluezenger

元件的封装问题，自己去琢磨吧！(*^__^*) 嘻嘻……

lgos12345

Dear Brother,

It is not clear to me what the exact problem is.

4 Y6 Z+ P+ \% W3 c. ^* s8 {" s0 [ Do you want to fix a component in it's position after the placement? If so just follow the procedure;

0 ]: ?/ z9 m' K2 R. c1 Select the component
2 right click the mouse
3 select properties
/ I; \0 h: r( d9 `/ |( b$ k4 click on glued
: U. R+ E: [+ s
Now the component is fixed at that position unless you remove the glued.
! ~( o+ T' A& y$ i  a8 A
Hope it helps you.

Regards

lgos

xiewu5

回复 3# lgos12345


    谢谢，你这个是保护元器件不被移动
* E  h" j$ E* {+ H' V我说的是，我开始在顶层布好局后，我想把他放到底层去，但一把它放到底层他就不是在原来的位置啦，都乱啦
6 z  b6 g7 r. G5 z' ?5 y' @2 _有没有方法使换层的时候位置不变啊

xiewu5

回复 2# bluezenger

, Z+ {- @; \$ S3 q% h
4 c, A4 O3 }! {/ e9 x- }) ?    封装没问题吧，是这样的，我在顶层布好局后我想把一些元器件放到底层去，一换他们的位置就都动啦，乱啦
有没有解决方法就是一换层后位置还在原处但位置不变

lgos12345

Dear Brother,
9 s8 E  i7 S9 l; H7 h- I' ^
& N8 F+ M: h! \" JI think there is a component on the top layer and you want to take it to the bottom layer without changing the X Y position. Is that so?
; \/ I( w* W2 C
In that case you can try this;

. y6 ]7 l) F2 B+ T% ?: |1  Make sure that the selection point of the component is in the center of the component.You have to do this in decal editor.

2 Go to Tools>Option>Design>Move Preference. Select Move by origin.

Now select the component and flip the side. It will change the side ( from top to bottom ) without changing the X Y co-ordinets.

Regards
% ]3 T8 o  e& r7 h" V$ i
lgos

xiewu5

回复 6# lgos12345
0 A/ i9 g( G. k2 a

& L5 B+ v0 ^1 D; I, X    对啦，现在位置不变啦 是我在设计封装时没有选择好原点
7 Q  K& v) @; |0 j9 t& z但现在又有新问题啦，一换层他的方向好像变啦

xiewu5

回复 6# lgos12345

) e; ~+ ]+ @( x5 p) R+ D
4 P* D: G7 M4 r$ Q# R* ~+ ~* I    直接在TOOL/OPTIONS里选MOVE BY MIDPOINT就行啦
但现在换层后方向反了，难道要选择后一个个旋转回来吗？

lgos12345

[size=100%][size=100%]Reply [size=100%][size=100%]8 # [size=100%][size=100%]xiewu5

9 u- B# z4 `5 CCan you send the pcb file so that I can look into it if you want me to do so.

xiewu5

回复 9# lgos12345

" g. T8 H0 y) V3 A, t6 Y  ?7 k
    我想在换层后，元器件位置方向不变，我现在位置不变啦，就是换层后都旋转了180度，怎么才能换层后不弯啊，谢谢啊

xiewu5

回复 9# lgos12345

xiewu5

回复 9# lgos12345


    这是换以前的

lgos12345

[size=100%][size=100%]Reply [size=100%][size=100%]11 # [size=100%][size=100%]xiewu5
5 d  a8 ^$ M& D: D8 X0 }9 `/ a1 X$ G

+ t# L* A  Y  Z$ T   Got the file. Which component ( for ex. c1,c2 etc)

xiewu5

所有贴片元器件换底层

lgos12345

OK.

* G8 E" C* h) V# Y. L- lI got the problem.
7 S  b9 P% U' z- l
; x, R& q) S# l4 a, y+ ZSelect C5 ( for ex.). Go to decal editor. The origin is on one of the pads. Keep the origin in the center of two pads. Exit the decal editor and then select all to make the change in all similar components. Now try to flip the component. It should work