[分享源代码]draw drill hole/将hole空可以输出至dxf

iuven · 发表于 2016-5-4 15:04

本帖最后由紫菁于 2017-11-3 14:30 编辑

EDA365 Skill 工具箱有这个工具，但是有问题，所以没事自己重写了一下；
主要是为了出dxf时将hole空能够输出到dxf文件，直接上代码：执行前========>

执行后=======>

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;draw drill holes as shape to BOARD GEOMETRY/DrillHole
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
axlCmdRegister( "drlh" `drill_hole_by)
num = 0
cnt = 0
pi = 3.141592
(defun drill_hole_by ()
saveVis = axlVisibleGet()
axlVisibleDesign(nil)
; set desired layers visible via one or more calls to
axlVisibleLayer("pin/top" t)
creat_layer_drlh()
;;turn_on_layer( layer)
formname = "./drlhole.form"
biuld_form_drlh(formname)
)
(defun creat_layer_drlh ()
; ########################################################
; Check for the existence of "BOARD GEOMETRY/DrillHole" layer
; ########################################################
if(axlIsLayer("BOARD GEOMETRY/Drillhole") == nil then
axlUIConfirm("You must have a\"BOARD GEOMETRY/DrillHole\" subclass defined")
axlLayerCreateNonConductor("BOARD GEOMETRY/Drillhole")
else
axlMsgPut("---Dirll holes to :BOARD GEOMETRY/Drillhole")
);end if
); end creat_layer_drlh
(defun biuld_form_drlh (formname)
(prog ()
pform = outfile(formname "w")
fprintf(pform "FILE_TYPE=FORM_DEFN VERSION=2\n")
fprintf(pform "FORM toolwindow\n")
fprintf(pform "FIXED\n")
fprintf(pform "PORT 20 10\n")
;PORT w h
fprintf(pform "HEADER \"byao\"\n")
fprintf(pform "TILE\n")
fprintf(pform "TEXT \"Drill Hole to Shape V1.0\"\n")
fprintf(pform "OPTIONS UNDERLINE BOLD\n")
fprintf(pform "TLOC 0 0\n")
fprintf(pform "ENDTEXT\n")
fprintf(pform "FIELD drawhole\n")
fprintf(pform "FLOC 1 2\n") ;FLOC x y
fprintf(pform "MENUBUTTON \"Drawhole\" 10 3\n")
fprintf(pform "ENDFIELD\n")
fprintf(pform "FIELD clearshape\n")
fprintf(pform "FLOC 1 5\n")
fprintf(pform "MENUBUTTON \"ClearShape\" 10 3\n")
fprintf(pform "ENDFIELD\n")
fprintf(pform "FIELD done\n")
fprintf(pform "FLOC 1 8\n")
fprintf(pform "MENUBUTTON \"Done\" 10 3\n")
fprintf(pform "ENDFIELD\n")
fprintf(pform "FLEXMODE EdgeGravityOne\n")
fprintf(pform "FLEX drawhole 0 0 1 1\n")
fprintf(pform "FLEX clearshape 0 1 0 0\n")
fprintf(pform "FLEX done 0 1 0 0\n")
fprintf(pform "ENDTILE\n")
fprintf(pform "ENDFORM\n")
close(pform)
form=axlFormCreate( (gensym) "drlhole.form"
`(e inner) `pform_Action_drlh t)
axlFormDisplay(form)
))
(defun pform_Action_drlh (form)
axlDBRefreshId(axlDBGetDesign())
(case form->curField
("done"
axlFormClose(form)
axlCancelEnterFun()
deleteFile(formname)
axlMsgPut("Done")
nil
)
("drawhole"
axlMsgPut("Draw Holes........" )
draw_hole_drlh()
t
)
("clearshape"
clear_shape()
t
)
);end case
);end defun
(defun unselect_object_drlh ()
(let (allsel)
axlSetFindFilter(?enabled '(noall shapes pins vias text) ?onButtons '(noall shapes pins vias text))
; axlSetFindFilter(?enabled '(all) ?onButtons '(all))
allsel = axlGetSelSet(axlAddSelectAll())
axlClearSelSet()
axlSetFindFilter(?enabled '(noall symbols) ?onButtons '(noall symbols))
allsel = axlGetSelSet(axlAddSelectAll())
axlClearSelSet()
)
)
(defun draw_circle (x y dia)
mycirpath = axlPathStartCircle((list x:y dia/2),0)
axlDBCreateCloseShape( axlDBCreateOpenShape( mycirpath, t,"BOARD GEOMETRY/Drillhole", nil))
)
(defun draw_oval_slot (x y w h r) ;;w=dia
;;x'=x*cos(r)-y*sin(r);y'=y*cos(r)+x*sin(r)
ll = ((x+((-w/2)*cos(pi*r/180)-(-(h-w)/2)*sin(pi*r/180))) : (y+(-(w/2)*sin(pi*r/180)+(-(h-w)/2)*cos(pi*r/180)))) ;;low left
ul = ((x+((-w/2)*cos(pi*r/180)-((h-w)/2)*sin(pi*r/180))) : (y+((-w/2)*sin(pi*r/180)+((h-w)/2)*cos(pi*r/180))))
ur = ((x+((w/2)*cos(pi*r/180)-((h-w)/2)*sin(pi*r/180))) : (y+((w/2)*sin(pi*r/180)+((h-w)/2)*cos(pi*r/180))))
lr = ((x+((w/2)*cos(pi*r/180)-(-(h-w)/2)*sin(pi*r/180))) : (y+((w/2)*sin(pi*r/180)+(-(h-w)/2)*cos(pi*r/180))))
mypath = axlPathStart( list(ll) )
mypath = axlPathLine( mypath, 0.0, ul )
mypath = axlPathArcAngle(mypath, 0.0, ur, t, 180)
mypath = axlPathLine( mypath, 0.0, lr)
mypath = axlPathArcAngle(mypath, 0.0, ll , t, 180)
myshape = axlDBCreateOpenShape( mypath, t,"board geometry/drillhole", nil)
axlDBCreateCloseShape( myshape)
)
(defun draw_rect_slot (x y w h r)
;;x'=x*cos(r)-y*sin(r);y'=y*cos(r)+x*sin(r)
ll = ((x+((-w/2)*cos(pi*r/180)-(-h/2)*sin(pi*r/180))) : (y+(-(w/2)*sin(pi*r/180)+(-h/2)*cos(pi*r/180)))) ;;low left
ul = ((x+((-w/2)*cos(pi*r/180)-(h/2)*sin(pi*r/180))) : (y+((-w/2)*sin(pi*r/180)+(h/2)*cos(pi*r/180))))
ur = ((x+((w/2)*cos(pi*r/180)-(h/2)*sin(pi*r/180))) : (y+((w/2)*sin(pi*r/180)+(h/2)*cos(pi*r/180))))
lr = ((x+((w/2)*cos(pi*r/180)-(-h/2)*sin(pi*r/180))) : (y+((w/2)*sin(pi*r/180)+(-h/2)*cos(pi*r/180))))
mypath = axlPathStart( list(ll) )
mypath = axlPathLine( mypath, 0.0, ul )
mypath = axlPathLine( mypath, 0.0, ur )
mypath = axlPathLine( mypath, 0.0, lr )
mypath = axlPathLine( mypath, 0.0, ll )
myshape = axlDBCreateOpenShape( mypath, t,"board geometry/drillhole", nil)
axlDBCreateCloseShape( myshape)
)
(defun draw_hole_drlh ()
clear_shape()
unselect_object_drlh()
axlSetFindFilter(?enabled '(noall pins) ?onButtons '(noall pins))
allpins = axlGetSelSet(axlAddSelectAll())
foreach(item allpins
if(item->isThrough then
padstack_ = item->definition
cnt++
case(padstack_->holeType
("circle_drill"
x = nthelem(1 item->xy)
y = nthelem(2 item->xy)
x_offset = nthelem(1 padstack_->drillOffset)
y_offset = nthelem(2 padstack_->drillOffset)
r = item->rotation
dia = padstack_->drillDiameter
draw_circle((x+(x_offset*cos(pi*r/180)-y_offset*sin(pi*r/180))) (y+(x_offset*sin(pi*r/180)+y_offset*cos(pi*r/180))) dia)
t
)
("oval_slot"
x = nthelem(1 item->xy)
y = nthelem(2 item->xy)
x_offset = nthelem(1 padstack_->drillOffset)
y_offset = nthelem(2 padstack_->drillOffset)
w = padstack_->drillSizeWidth
h = padstack_->drillSizeHeight
r = item->rotation
draw_oval_slot((x+(x_offset*cos(pi*r/180)-y_offset*sin(pi*r/180))) (y+(x_offset*sin(pi*r/180)+y_offset*cos(pi*r/180))) w h r)
t
)
("rectangle_slot"
x = nthelem(1 item->xy)
y = nthelem(2 item->xy)
x_offset = nthelem(1 padstack_->drillOffset)
y_offset = nthelem(2 padstack_->drillOffset)
w = padstack_->drillSizeWidth
h = padstack_->drillSizeHeight
r = item->rotation
draw_rect_slot((x+(x_offset*cos(pi*r/180)-y_offset*sin(pi*r/180))) (y+(x_offset*sin(pi*r/180)+y_offset*cos(pi*r/180))) w h r)
t
)
(t
x = nthelem(1 item->xy)
y = nthelem(2 item->xy)
printf("Wanning:%f %f %s\n" x y padstack_->holeType)
)
);case
);end if
);end foreach
unselect_object_drlh()
; restore visiblility
axlVisibleSet(saveVis)
axlVisibleLayer("BOARD GEOMETRY/Drillhole" t)
; note no need to make a call to axlVisibileUpdate because
; the visisbility changes are a wash
axlVisibleUpdate(t)
axlMsgPut("---Total of throughhole : %d" cnt)
cnt=0
)
(defun clear_shape ()
unselect_object_drlh()
saveVisx = axlVisibleGet()
axlVisibleDesign(nil)
; set desired layers visible via one or more calls to
axlVisibleLayer("BOARD GEOMETRY/Drillhole" t)
; set find filter for objects to find
axlSetFindFilter(?enabled '(noall shapes) ?onButtons '(noall shapes))
axlAddSelectAll()
axlDeleteObject(axlGetSelSet())
; restore visiblility
axlVisibleSet(saveVisx)
)

复制代码

游客，如果您要查看本帖隐藏内容请回复

hyper311 · 发表于 2017-9-12 10:23

hyper311 发表于 2017-9-12 09:39
我运行会报错E- (SPMHDB-69): Incomplete arc segment data. E- (SPMHDB-187): SHAPE boundary may not cro ...

Incomplete arc segment data.
这个错误是，焊盘中存在直径为0的过孔
E- (SPMHDB-187)这个错误我再看看

這侽孓譙悴丶 · 发表于 2018-1-5 10:40

jordanli22 发表于 2018-1-5 10:26
请问：“EDA365 Skill 工具箱有这个工具，但是有问题” eda365的有什么问题？？

应该没什么问题吧，论坛的那个是先生成钻孔尺寸的shape，然后你再自己手动去出dxf即可！

fruitpig345 · 发表于 2018-3-5 10:07

請教樓主執行後出現下面error 是甚麼原因
Command > drlh
---Dirll holes to :BOARD GEOMETRY/Drillhole
Draw Holes........
E- *Error* fprintf/sprintf: format spec. incompatible with data - nil

vivianwu0320 · 发表于 2016-5-6 09:27

謝謝分享

wuyuhe · 发表于 2016-5-17 11:39

谢谢分享

GSO_library · 发表于 2016-5-18 17:36

谢谢分享~~~~

wu55 · 发表于 2016-7-7 16:03

謝謝分享

koncc · 发表于 2016-7-11 10:11

感謝分享

Apis · 发表于 2016-9-28 11:39

16.6没有任何输出。。。
需要已安装EDA365 tool么？

hy20060614 · 发表于 2016-11-9 09:01

谢谢分享

wancai9550 · 发表于 2016-11-9 09:18

感謝分享

361553894 · 发表于 2016-11-15 20:59

我没贡献值了么？？

mentorkk · 发表于 2016-11-16 03:07

谢谢分享

hy20060614 · 发表于 2016-11-22 18:07

谢谢分享

lisheng1255 · 发表于 2016-11-23 08:34

看不懂

lisheng1255 · 发表于 2016-11-23 08:34

lisheng1255 发表于 2016-11-23 08:34
看不懂

能解释一下吗？

bingshuihuo · 发表于 2017-4-21 14:11

不错！！！！！！！！

		自动登录	找回密码
密码			注册

[分享源代码]draw drill hole/将hole空可以输出至dxf

本帖子中包含更多资源

评分

点评

点评

推荐内容 /1