术语解释“zero crossing counter”

xiongbindhu

术语解释“zero crossing counter”,干啥用的？

skatecom

zgq800712

骚年，google会用不？

风吹摇摆

zgq800712 发表于 2013-6-24 22:58
骚年，google会用不？

5 a: ?0 y( o2 c8 m不要用古狗，用百度！

木头脑瓜

风吹摇摆 发表于 2013-6-25 08:37
不要用古狗，用百度！

狗主的地盘敢不用古狗^_^

超級狗

5 p0 m8 A# l0 ~2 }2 r. M4 ~* x
用途很廣，我找到的並非全部，大家參考一下好了。

2 y5 T7 O- ^* }; F& s零交越計數器（Zero Crossing Counter）

解釋︰
以零做為基準點的計數器，當訊號跨越零點時才計數。
4 w9 O7 w7 z) p6 {4 j0 L. Z
2 q) _9 X4 e' H$ D7 i優點︰
6 d- {* V2 G# d+ L7 m  a* P( x

• 對於不斷變換的訊號有較精準的頻率量測值。
• 有些控制希望在零點時做變化調整，才不會有副作用。
  , H, I0 b. b1 v! B! ]( L

  M( y7 b3 x4 Q+ ]5 M  I& G
1 X0 D( v) v5 `* k3 P6 t' ]2 m應用︰

• 影像處理
• 語音辮識
• 光學分析
• 都普勒（Doppler）雷達
• 電源供應器功率因子調整（PFC）。
  

# y+ S+ V$ L( U8 A- |......
/ `8 R- g4 M. n7 Y& a4 a) d
$ M5 Q6 E0 S7 B4 B9 {( I' F0 I- T我以前的工作經驗，交換機（PBX）有用到。振鈴產生器（Ring Generator）會在零交越（Zero Crossing）時才將振鈴繼電器（Ring Relay）切換回正常的位置，避免電話端殘存的高電平回灌交換機（PBX），將振鈴產生器（Ring Generator）打死！
5 u4 V7 p: f: t  }
{:soso_e163:}
/ `4 i# L; @2 S4 h& V# p9 ~
0 @/ D* [& e7 W+ b

xiongbindhu

超級狗 发表于 2013-6-25 09:07
. j& g2 F- Q0 R用途很廣，我找到的並非全部，大家參考一下好了。
5 K2 G7 m0 D# t6 x4 h5 `5 V+ x
零交越計數器（Zero Crossing Counter）

; T& \: B$ U  }5 \9 h, x# d* J, `{:soso_e163:}
我看的资料这边，那应该是用来测量信号频率的。
5 R8 u. ~; s0 ^+ b3q，gogo

zgq800712

Zero Crossing Counter

8 a) _2 i: |. G8 W; [( k6 m
7 h  G% a! R2 n  t1 Q( j" y8 o! m. ^
  A7 g3 [8 `; WIn some DSP applications, it can be very helpful to know how many times your signal has crossed the zero-line (amplitude origin).
: `' m. D7 G4 g8 b) \" V$ X
2 v- g4 e8 Y! t: hHow is this helpful?  Well, zero-crossings can tell you very quickly if your signal is composed of high frequency content or not.  Let's say your sample rate is 50kHz and over a small window of 1,000 samples there are 500 zero-crossings.  That would mean that every two samples crosses the zero-line (i.e. 12.5kHz)

. F) G2 Z' j  N7 I" IIn speech processing, the zero-crossing counts can help distinguish between voiced and un-voiced speech.  Un-voiced sounds are very noise-like ('Shh' and 'Sss' for example).  In addition, zero-crossings could also be used to determine if your signal has a DC offset.  If you signal is 'muted' and you are not seeing alot of zero-crossings might mean that your signal is offset from the zero-line

0 T' g- U4 s; u1 ^5 `3 k& V, Z- |One nice thing about the matlab code below is that it is implemented in a very DSP-friendly way.  It ports very easily into C-Code and does minimizes the amount of conditional statements for faster processing time.