|
|
EDA365欢迎您！
您需要 登录 才可以下载或查看，没有帐号？注册
x
本帖最后由 tchming 于 2011-3-10 22:58 编辑 # @7 m4 K! h1 ~- W, |# { L
! C+ Q& K/ `9 v& n$ `
请问版主orcad capture 16.3中测试管脚如何命名啊，我用testpin1、testpin2等
& l, s$ M" G& M8 y ~4 B3 B仿真时报错，具体如下：
& p/ L# \% k; i7 ^7 XWARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN1.
2 Y& ^! P& U+ XWARNING [NET0102] Illegal net name SIGNAL SOURCE1_N00942.# u+ C- i# y/ O% C- }3 U
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N01010.
9 r5 _$ {3 w2 _0 dWARNING [NET0102] Illegal net name SIGNAL SOURCE1_N00942.2 |' }" M7 T# q- P7 z% b5 Q3 R, _0 H
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN1.) @/ E/ K9 _1 N0 G6 K# u
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN2.
+ U1 E' f( R7 ~: s9 _WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N01010.1 E" O, C9 N* e A+ S" L) n9 ^
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN2., u5 ^. P, s4 X z' _, l2 J! y* M4 L& E( B
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N00942.
7 @% I) f" i+ G! XWARNING [NET0102] Illegal net name SIGNAL SOURCE1_N01010.
( |3 r/ y* L0 C; VWARNING [NET0102] Illegal net name 5-POLE SHAING1_N03569.
$ h* a6 p4 {( `: q1 ]WARNING [NET0102] Illegal net name 5-POLE SHAING1_N03569., O3 u/ E; K) {8 q0 L0 N
WARNING [NET0102] Illegal net name 5-POLE SHAING1_N03569.; v2 o K/ P' b9 J# y
WARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_A275 NO_2_N00953.. f4 Z/ j$ @' `% D2 z
WARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_A275 NO_2_N00961.
4 p5 W$ v& G6 z' p' M: w, ~" | r8 YWARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_A275 NO_2_N00953.
) O1 E# X9 u; O1 p8 X9 `0 PWARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_TESTPIN6.& J& y9 h8 P& |8 A- i7 c9 f
: X, T" }4 E( Q- @
& {& |. \6 {7 G A4 @% B0 ]
求指教
3 |8 Q) m* r' O% p. D. c. S0 d7 _- M7 ~/ i- o- M' K' ^
|
|
/1 
发表于 2011-3-10 22:50
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
支持！
反对！
楼主