大家帮我看一下仿真的问题 ？？

xiaowenwu1989

   如附档图，我仿真时出现一个这样的对话框，请问一下我应该怎样弄呢？

1 s. a) s3 b: J) y# r5 P

wwddss_1976

查看session log

jacklee_47pn

貌似圖片中紅色框框中沒打點(沒連接上)。導致三極管 E 極沒連上。

xiaowenwu1989

wwddss_1976 发表于 2016-10-19 20:22
6 t# e, s/ a5 |; P" N- \6 f. r' f# q查看session log

9 F. _4 C1 }/ @4 X就看到一个这样的东东：
" X4 w1 s3 `* `) w" y0 O0 y( a2 F**** 10/19/16 15:28:12 ***** PSpice 16.6.0 (October 2012) ***** ID# 0 ********
9 b5 Z+ p! Q+ K1 Q1 {% y+ \; O- Y
' P; r0 C6 |+ C- S- W ** Profile: "SCHEMATIC1-test123"  [ D:\CADENCE\SPB_16.6\SPB_DATA\test123-PSpiceFiles\SCHEMATIC1\test123.sim ]

( Z( d  r; g5 C4 J' k1 |
****     CIRCUIT DESCRIPTION


******************************************************************************

: _8 E! y& h0 m1 N1 H0 \" \2 U


** Creating circuit file "test123.cir"
** WARNING: THIS AUTOMATICALLY GENERATED FILE MAY BE OVERWRITTEN BY SUBSEQUENT SIMULATIONS
- q" c7 P6 F8 A1 @! a" K
*Libraries:
* Profile Libraries :
* Local Libraries :
( [8 I: S2 g6 W2 D* From [PSPICE NETLIST] section of C:\DOCUME~1\XIAOWE~1\LOCALS~1\Temp\16.6.0/PSpice.ini file:
.lib "nom.lib"

*Analysis directives:
6 C. B* y0 y! ^; h- Y---------------$
( U7 A$ E( W) Q0 Z* \7 {. bERROR(ORPSIM-16276): Can't find library
5 x2 S* U  D4 O3 v6 a+ j6 y  ?6 t% h# y+ w.TRAN  0 1000ns 0
1 H* H) e. X, r! q/ u.OPTIONS ADVCONV
.PROBE64 V(alias(*)) I(alias(*)) W(alias(*)) D(alias(*)) NOISE(alias(*))
3 i* I0 q/ d5 @0 C) k2 }. C; k+ ^.INC "..\SCHEMATIC1.net"
. e7 Q5 H3 ]* P& l
6 m; P+ ~! C: T. s" {
( X* g) w& O* q. H4 ~
: [3 H+ r5 U. `8 f: w+ V**** INCLUDING SCHEMATIC1.net ****

**** RESUMING test123.cir ****
.END

3 r+ Y4 `" O/ T7 {2 T& X

wwddss_1976

Can't find library，没有把相关库添加进去

xiaowenwu1989

wwddss_1976 发表于 2016-10-20 18:21
1 }& \8 Y7 e) a' C. U: }7 |9 xCan't find library，没有把相关库添加进去

   哥你帮我看一下，我不知道怎么弄


9 e2 V' T/ c. j1 Z" g5 z$ S$ RCreating PSpice Netlist
INFO(ORNET-1041): Writing PSpice Flat Netlist D:\CADENCE\SPB_16.6\TOOLS\CAPTURE\test123-PSpiceFiles\SCHEMATIC1\SCHEMATIC1.net
. ]' G3 }! n( h9 u4 U; L( k. uINFO(ORNET-1169): Unable to open the property mapping file: devparam.txt. To resolve this problem, ensure that PSpice.ini exists at the correct location. After that check Library Path in simulation settings contains <installation-path>/tools/pspice/library path and then create the netlist again.
" k! ]6 P4 p0 f" v' R, g, aINFO(ORNET-1162): Unable to create design property file.
! q+ J1 x; k% r; w

xiaowenwu1989

wwddss_1976 发表于 2016-10-20 18:21
0 e6 t" p4 y" {" C4 g! U. A& d" tCan't find library，没有把相关库添加进去

xiaowenwu1989

xiaowenwu1989 发表于 2016-10-21 09:39

大神们怎么弄
- f9 G* ^+ G1 B8 \1 K; a3 [

wwddss_1976

把相应库文件添加到nom.lib所在位置