|
EDA365欢迎您!
您需要 登录 才可以下载或查看,没有帐号?注册
x
本帖最后由 fenghaili 于 2016-10-20 20:40 编辑 3 p/ ~. g, o4 n' r
! f. i: |0 I3 h9 I$ [
比如:灰色框是板框,红色环形区域要开阻焊,结构给了开阻焊区域的外框和内框,我把结构图外框 直接zcopy成solermask层的shape,结构图内框 如何zcopy成这个shape的void?以实现环形开阻焊?4 P5 N) {) Z: d' M% e2 |6 M, s" U
+ @, ]; E( g$ U/ i+ e
4 h7 _0 `/ b' c4 `( l( L7 `找到了一个办法。自己看吧!$ t2 U, K( w0 y8 F' h: ~3 u1 J
# n6 k8 L7 {1 e3 Q& c5 d, y* p0 g" t$ i* t8 O3 \# B
Create a void from a shape in AllegroStarted by spbae on 16 Nov 2010 9:21 AM. Topic has 1 replies and 10296 views. 3 r0 o( T% @/ s0 ^6 x
Last post on 16 Nov 2010 4:09 PM by redwire.3 S! l9 B; Z. M7 E0 I1 [
/ [7 J! P% ?. K" D4 l* A
7 ? r! K# X3 d
; [2 t/ G" h. B6 Z
4 u k% [2 F' [% v9 \% D 6 ?# Q4 e& V6 d- Q7 e
5 |6 x' P0 b! d5 M$ a2 u ~ d, _, g0 ]! \& ~" z- @+ B
5 Q5 z/ M+ z/ @& L$ w# ?# z4 C- B) j3 K9 G( I( C+ R9 J. Y
; [/ r. O" o& T$ J7 r2 H2 Q3 s, D
Hi all,
. ?6 z% x+ u* `I am trying to create a ring of exposed copper at the edge of a board by creating a shape on the solder mask top, however I can't seem to make an actual ring rather than a big filled plane. I can use z-copy to get the outer edge from my route keepin, but I can't figure out how to use a shape to generate a void (I would love to use z-copy to make the void the same shape as the route keepin, but contracted by 30 mils). Any suggestions, or is there something really obvious that I'm missing here?" @. q9 O7 C; _
Thanks! sp7 J7 y' ~+ v8 \0 k
* t0 Q8 a; t& x3 C[edit]
* k# g/ p% k% oI found a way to do this. If you create two unfilled shapes that represent the inner and outer boundaries of the ring (I did this by z-copying the keepin referenced above, once the same and once contracted by 30 mils, and decomposing both resulting line/arc items) compose a shape using these, it creates the ring exactly as I wanted it. I was going to delete this post, but I figured anyone looking for this might want my solution...+ @; L- [7 ?6 K% H! N7 b, I
7 Y( K0 d) e4 o$ f }. b8 y9 g3 G6 z+ @4 Y; K. U. u& c# N
|
|