上传“如何在OrCAD定義Allegro可swap的排阻”

hu311

详见附件文档！

风雨者

为什么会出现子图中的阻排位号不能编号,始终为RN1,导致检查不通过,不能生成网表?
8 o- g: r* r- @, M3 Q
) U+ k' P8 }' r" A0 f: h--------------------------------------------------
Checking Schematic: RN22 RN-8P4R-1
* N/ x! `! z( Y& x5 Q--------------------------------------------------
; @$ r) h- s, L4 }+ ~Checking Electrical Rules
2 z" p- C& l) W4 l
: ?' X7 v: e4 I5 pChecking for Unconnected Nets
6 p! s/ d8 {3 a5 R7 @2 T  s2 G
Checking Off-Page Connections

9 t3 U/ n# M2 b/ D! Q& a9 zChecking Pin to Port Connections
" y8 b0 s) s* T6 @
3 S0 d8 ]: ]( T$ SChecking for Invalid References

Checking for Duplicate References
, v" E( q) a" x0 c( uERROR [DRC0010]   Duplicate reference RN22/RN1D:  RN-8P4R-1, RN-8P4R  (5.10, 2.50)
ERROR [DRC0010]   Duplicate reference RN22/RN1A:  RN-8P4R-1, RN-8P4R  (5.10, 2.20)
0 {! r9 r7 |; R- w7 I0 ?, kERROR [DRC0010]   Duplicate reference RN22/RN1B:  RN-8P4R-1, RN-8P4R  (5.10, 2.30)
+ h: E9 |. W/ }) z+ g; aERROR [DRC0010]   Duplicate reference RN22/RN1C:  RN-8P4R-1, RN-8P4R  (5.10, 2.40)

许汉洲

风雨者 发表于 2008-10-28 20:22
为什么会出现子图中的阻排位号不能编号,始终为RN1,导致检查不通过,不能生成网表?
  
--------------- ...

重复管脚，重复管脚连接在不同网络，建议修改原理图。

hukee

一直都不知道allegro中 swap pin是怎么用的。

qqtolm

不错，先看看

sibling520

这个没有说明后续怎么把交换后的管脚标到原理图上啊

panadol

多谢分享！！

mashiquan123

{:soso_e179:}

asus0929

Thanks for sharing..

252631

good,谢谢!

风雨者

可为什么生成网表时出错呢?
  Check for incorrect packaging of all devices in RN1.
#569 Error   [ALG0045] multiple pin 4's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 63.50).
8 \; T; t% y0 x0 e. U# m              Check for incorrect packaging of all devices in RN1.
#570 Error   [ALG0045] multiple pin 5's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 63.50).
              Check for incorrect packaging of all devices in RN1.
#571 Error   [ALG0045] multiple pin 1's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 55.88).
              Check for incorrect packaging of all devices in RN1.
#572 Error   [ALG0045] multiple pin 8's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 55.88).
" @7 A/ B, |: |' `( g0 Q9 r              Check for incorrect packaging of all devices in RN1.
3 X9 A$ a8 ]; _* \% g#573 Error   [ALG0045] multiple pin 2's which have different nets connected for RN1: SCHEMATIC1, RN-8P4R (129.54, 58.42).
7 J6 c3 P/ y" U+ V1 J% d              Check fo
r incorrect packaging of all devices in RN1.

风雨者

好方法!讲解很细致!赞一个!

lbq211

定一
1 h* Z# q, R5 {9 Q7 d个

abyass

顶，好东西

fhjltw

及时雨啊，正需要，谢！

lihuizju

谢谢。下来看看