请各位大侠帮我看一下这个ibis模型怎么了

huzhongmoshui

请各位大侠帮我看一下这个ibis模型怎么了，这是我从TI官网上下载的，在编译的时候报错：
ERROR - Model Model67: The [Rising Waveform]
8 v% _) i/ @3 `; _      with [R_fixture]=50 Ohms and [V_fixture]=0V
      has TYP column DC endpoints of  0.00V and  1.19v, but
% b+ s: a3 Y) l5 r  p/ m      an equivalent load applied to the model's I-V tables yields
( u# [; d" W  j3 _      different voltages ( 0.00V and  0.98V),
# ]9 v9 Q' v$ D" b) s/ _      a difference of  0.00% and 21.94%, respectively.
4 [+ S. `7 m$ J, E3 WERROR - Model Model67: The [Falling Waveform]
& O. h/ s$ w- G) t# d& a" F      with [R_fixture]=50 Ohms and [V_fixture]=1.8V
3 F9 \* V9 g7 h7 x. J$ _0 b  |! h+ |      has TYP column DC endpoints of  0.63V and  1.80v, but
      an equivalent load applied to the model's I-V tables yields
6 X7 }. O+ \9 R( G      different voltages ( 0.88V and  1.80V),
6 G& e! b" e& ~% C7 x) E( f4 n      a difference of 27.06% and  0.00%, respectively.
# k, W) V6 R( K1 dWARNING - Model Model67 Pulldown Minimum data is non-monotonic
6 r! _$ s; d6 x* x5 T. `/ G! P& q3 O) T* ?WARNING - Model Model67 Pullup Maximum data is non-monotonic
ERROR - Model Model67: The [Rising Waveform]
) i( B% Y( `4 p, u4 S      with [R_fixture]=50 Ohms and [V_fixture_max]=0V
- K, K6 z  _  H3 c( K      has MAX column DC endpoints of  0.00V and  1.38v, but
2 \* v- _0 T2 E$ a1 v) j      an equivalent load applied to the model's I-V tables yields
      different voltages ( 0.00V and  1.15V),
' g- o' k; l" L' D: M      a difference of  0.00% and 20.19%, respectively.
ERROR - Model Model67: The [Falling Waveform]
      with [R_fixture]=50 Ohms and [V_fixture_max]=1.89V
      has MAX column DC endpoints of  0.53V and  1.89v, but
) R8 @  _  E& V      an equivalent load applied to the model's I-V tables yields
$ q0 i- K' G2 k+ P      different voltages ( 0.84V and  1.89V),
      a difference of 29.38% and  0.00%, respectively.

# ~: k6 [, t% L& k/ D: Q哪位大侠知道的帮帮忙啊，不知道的也帮我分析分析吧。
! d% ~; C0 ~- ^) u: B我这有一段解释：This happens because the function acdc_VI_Given_VIC_VR() in acdc.c improperly
9 t- A4 g7 t  X7 breports the I-V/V-t intersection whenever it lies above the highest voltage in
; J+ p5 H! B) N0 x" y) [- }  Vthe I-V characteristic.  This defect is likely to show itself in models lacking
# P- {7 O& U/ t! o+ g+ ?clamp tables and in which either the [Pullup] or [Pulldown] table does not cover
the range from -Vcc to 2*Vcc.  Any open drain or open source model which lacks
* t7 D; E" W) b& P3 Xclamp tables is likely to meet these conditions because it is likely to lack
either the [Pullup] or [Pulldown] table.  In this test case, IBISCHK generates
error messages only for the MIN data because the highest voltage in the high-
state I-V characteristic for the minimum corner lies below the 1.8 V V-T
operating voltage.
3 t8 w3 C! {9 n5 @3 Z  K6 x: }9 }
但是缺少该怎么做啊