请高手帮看下，我新手

gonna_k3

#1   WARNING(SPMHNI-192): Device/Symbol check warning detected.

! I' M9 K1 F' y' P4 c! s8 dERROR(SPMHNI-196): Symbol 'SO-8-B' for device 'OP27_SO-8-B_OP27' has extra pin '1'.

! H/ r: x0 u& u+ c) f2 w. RERROR(SPMHNI-196): Symbol 'SO-8-B' for device 'OP27_SO-8-B_OP27' has extra pin '5'.

ERROR(SPMHNI-196): Symbol 'SO-8-B' for device 'OP27_SO-8-B_OP27' has extra pin '8'.
- i" B/ d9 C5 N/ F/ ]1 f% r
#2   WARNING(SPMHNI-192): Device/Symbol check warning detected.

#3   WARNING(SPMHNI-316): Property warning detected.
8 Z' i' D+ v9 v( r8 c; w
/ C4 C2 y2 N: J$ m, }" EWARNING(SPMHNI-301): Problems with component 'R7'. Error with component property '' and value 'VOLTAGE': 'RVMAX'.

' x' j2 m* |. \" n#4   WARNING(SPMHNI-316): Property warning detected.


5 N4 J( j  p: ^. I什么意思啊？原来装orcad时可以导入layout，但是现在换allegro用capture导入pcb就出现这个问题了， Error with component property什么意思呢？
, J# `3 @6 g* lvalue 'VOLTAGE': 'RVMAX'是默认的，现.应该改成什么呢？
4 f% L/ t3 V. e+ W0 \'OP27_SO-8-B_OP27' has extra pin '8'.说我的op有多余管脚？是原理图里的part有问题还是封装有问题呢？op有多余的管脚很正常的啊
6 w% D/ C: }/ p/ H! t+ Y请高手帮忙下

疯狂杀戮

- o  n- D; o. V  [3 o* t& }3 K这是Voltage和Current的设置，木动，都是默认值

疯狂杀戮

#1   WARNING(SPMHNI-316): Property warning detected.
" i: E0 t+ o  W( K# l. ]
WARNING(SPMHNI-301): Problems with component 'R1'. Error with component property '' and value 'VOLTAGE': 'RVMAX'.

4 t4 T: n- s- u( A#2   WARNING(SPMHNI-316): Property warning detected.

WARNING(SPMHNI-301): Problems with component 'C1'. Error with component property '' and value 'VOLTAGE': 'CMAX'.
我也遇到了，求解

土豆小飞侠

这个没有见到不敢瞎说!

27ing

我认为问题应该是出在“extra pin……”吧   我还没用上Allegro   大家帮忙拍砖吧

gonna_k3

我随便试了下，用allegro自带的库，op37用封装dip8-3，还是提示出错
+ b$ d" Y7 F7 T  {0 B! [7 m/ `ERROR(SPMHNI-196): Symbol 'DIP8_3' for device 'OP37_DIP8_3_OP37' has extra pin '1'.

ERROR(SPMHNI-196): Symbol 'DIP8_3' for device 'OP37_DIP8_3_OP37' has extra pin '8'.
3 M0 _* _( t7 {. Z
ERROR(SPMHNI-196): Symbol 'DIP8_3' for device 'OP37_DIP8_3_OP37' has extra pin '5'.
5 z1 K9 Q% A7 M* C# V( D# g2 O这个要怎么解决呢？用allegro的朋友帮帮忙啊

gonna_k3

Problems with component 'R7'. Error with component property '' and value 'VOLTAGE': 'RVMAX'.
这个又是什么意思呢？
' p8 U% M( E1 r; r1 T1 B我把VOLTAGE的默认值RVMAX删掉就不提示了，难道capture的默认值是错的？
还望用allegro的兄弟们指点下

袁荣盛

原理图示意图和PCB封装的引脚没有对应好
# y- A( f: c8 B) f另外一个问题没亲眼见到不敢瞎说