大家帮我看一下仿真的问题 ？？

xiaowenwu1989

   如附档图，我仿真时出现一个这样的对话框，请问一下我应该怎样弄呢？
0 Q; a" j4 C4 s4 c7 A) B: ?

wwddss_1976

把相应库文件添加到nom.lib所在位置

xiaowenwu1989

xiaowenwu1989 发表于 2016-10-21 09:39

大神们怎么弄

xiaowenwu1989

wwddss_1976 发表于 2016-10-20 18:21
Can't find library，没有把相关库添加进去

; S/ |' _( ~; U! a
5 |7 p  u2 N2 S/ d% E' a

xiaowenwu1989

wwddss_1976 发表于 2016-10-20 18:21
4 R# \  y  ^3 T  R' ]Can't find library，没有把相关库添加进去

   哥你帮我看一下，我不知道怎么弄


Creating PSpice Netlist
INFO(ORNET-1041): Writing PSpice Flat Netlist D:\CADENCE\SPB_16.6\TOOLS\CAPTURE\test123-PSpiceFiles\SCHEMATIC1\SCHEMATIC1.net
INFO(ORNET-1169): Unable to open the property mapping file: devparam.txt. To resolve this problem, ensure that PSpice.ini exists at the correct location. After that check Library Path in simulation settings contains <installation-path>/tools/pspice/library path and then create the netlist again.
) q; z* K  ^0 o$ S( nINFO(ORNET-1162): Unable to create design property file.

. p* Z7 N9 h. r; R; T/ a

wwddss_1976

Can't find library，没有把相关库添加进去

xiaowenwu1989

wwddss_1976 发表于 2016-10-19 20:22
查看session log

4 R3 o8 f4 J4 B; \1 u就看到一个这样的东东：
# a3 a0 ^$ `2 y. z& Y/ I**** 10/19/16 15:28:12 ***** PSpice 16.6.0 (October 2012) ***** ID# 0 ********
% `+ Y* x( e9 |) l0 }- _5 f0 O
1 h1 h! X" K+ Q/ ]8 J2 F" d' a ** Profile: "SCHEMATIC1-test123"  [ D:\CADENCE\SPB_16.6\SPB_DATA\test123-PSpiceFiles\SCHEMATIC1\test123.sim ]
+ u; N9 j+ B7 v" m6 b

****     CIRCUIT DESCRIPTION
8 S& j: A  c$ q, }

******************************************************************************
9 b/ S$ c/ q" f" O. a2 P

; _# a; _- l: _. s/ |

/ E/ c  f: }0 t) l: Y+ ]' G: _** Creating circuit file "test123.cir"
** WARNING: THIS AUTOMATICALLY GENERATED FILE MAY BE OVERWRITTEN BY SUBSEQUENT SIMULATIONS

*Libraries:
* Profile Libraries :
* Local Libraries :
, |. B' p: x; B- f8 J( ?3 C- P1 Q* From [PSPICE NETLIST] section of C:\DOCUME~1\XIAOWE~1\LOCALS~1\Temp\16.6.0/PSpice.ini file:
.lib "nom.lib"
# X5 U# ]1 g/ `' H
  ?7 H2 ~" ?8 Y*Analysis directives:
. G9 P/ S# e* c! M8 A6 m---------------$
ERROR(ORPSIM-16276): Can't find library
.TRAN  0 1000ns 0
.OPTIONS ADVCONV
.PROBE64 V(alias(*)) I(alias(*)) W(alias(*)) D(alias(*)) NOISE(alias(*))
.INC "..\SCHEMATIC1.net"

) {5 P; v& y8 `& L4 ?$ S3 |1 L
1 ]) Z8 v6 v1 ^/ B0 J8 ?1 g$ F" G
  c4 _2 x8 u& O: c: S**** INCLUDING SCHEMATIC1.net ****

**** RESUMING test123.cir ****
% ]5 l& ]9 P% x! \.END


jacklee_47pn

貌似圖片中紅色框框中沒打點(沒連接上)。導致三極管 E 極沒連上。

wwddss_1976

查看session log