【分享源代碼】建立動態選單/添加自定义菜单

XYX365 · 发表于 2016-1-25 11:09

本帖最后由 XYX365 于 2016-1-25 13:42 编辑

如何把自己的菜单插入到allegro menu,使用動態選單

;filename:fDynamicMenus.il
;此程式只適用於Allegro v16.3以上
;必須直接加載到allegro.ilinit檔裡面,不能在其他地方載入此程式
;此程式可以設計成中英文語言的選單

; Load: load("fDynamicMenus.il")
;附件程式不包含選單上的任一程式工具

;filename:fDynamicMenus.il
;此程式只適用於Allegro v16.3以上
;必須直接加載到allegro.ilinit檔裡面,不能在其他地方載入此程式
;此程式可以設計成中英文語言的選單
; Load: load("fDynamicMenus.il")
setShellEnvVar("LANG=ENG") ;強制設定為英文選單
case(getShellEnvVar("LANG")
("GB"
;這裡是擺放簡體中文位置,沒有完成,必須自行建立
lSkillMenu = '(
(popup "EDA365 Skill for Test") ;主選單上的名稱
("Chinese Transfer" "(fnChineseTransform)") ;第一個字串是顯示在選單上,第二個字串是執行命令
("Quick Open" "filemgr") ;程式選單項目
(separator) ;區格線
("Netin,3rd Party" "netin3rd_protel")
("Compare Net_Changes" "gnetrpt")
("Compare BRD_Changes" "component_changes")
("Clear Layout TempFile" "tmpdel")
("Check Height" "heightchk")
("Hilight TestPoint Net" "hlnpt")
("Set_drillkey" "setdrill")
("Set Design Color" "s1")
("Show Height/width" "draw targets")
("Add Layer" "addlayer")
("Calc Trace Width" "twcal")
("Calc Via Quantity" "viacal")
("Cut Line" "clinecut")
("Cut Shape" "cutshape")
("Check width" "chgew")
("Etch Cross Check" "ecp")
(popup "Text Function") ;子選單名稱
("Edit TextBlock" "settxtpw")
("SilkScreen Export/inport" "text_out_in")
("Move Text2Center" "r2c")
("Check_NoRefdes" "ch_noref")
("Check_refdes_direction" "ch_dir")
("Check_text_grap" "ch_text_overlap")
(end)
(popup "SplitPlane")
("SplitPlane_CreateLayers" "SplitPlane_CreateLayers")
("SplitPlane_CreateShapes" "SplitPlane_CreateShapes")
(end)
(popup "DataBase Check")
("DataBase &Check..." "dbdoctor")
("DANGLING CHECK" "dangling")
("DumpVia CHECK" "check_dvia")
(end)
(popup "TAPEOUT")
("Artwork..." "artwork")
(separator)
(popup "AUTO DRILL")
("SET NCcustom" "setnccus")
("Drill Legend" "nclegend")
("Drill Route" "ncdr")
(end)
("Setting FilmControl" "efilm")
("Auto CreateArtWork" "ns_gerber")
("Output GFile" "outfilm")
("draw pin hole" "draw pin hole")
("Ouput DXF/RefPdf/IPC356" "odxf")
("Ouput SymLoc" "inform")
(popup "Sort Output File")
("Move Gfile" "sortgfile")
("Zip Gerber" "gzip")
(end)
(end)
("Export CAD" "cadout")
(separator)
(popup "[ System Tools ]")
("[ Snap Screen ]" "system snippingtool")
("[ Run Notepad ]" "system notepad")
("[ Run Calculator ]" "system calc")
("[ Run Paint ]" "system mspaint")
("[ Run CMD ]" "system")
(end)
(end)
)
)
("BIG5"
;這裡是擺放繁體中文位置,沒有完成,必須自行建立
lSkillMenu = '(
(popup "EDA365 Skill for Test") ;主選單上的名稱
;第一個字串是顯示在選單上,第二個字串是執行命令
("\244\244\244\345" "(fnChineseTransform)") ;中文碼轉八進位的ASCII碼
("Quick Open" "filemgr") ;程式選單項目
(separator) ;區格線
("Netin,3rd Party" "netin3rd_protel")
("Compare Net_Changes" "gnetrpt")
("Compare BRD_Changes" "component_changes")
("Clear Layout TempFile" "tmpdel")
("Check Height" "heightchk")
("Hilight TestPoint Net" "hlnpt")
("Set_drillkey" "setdrill")
("Set Design Color" "s1")
("Show Height/width" "draw targets")
("Add Layer" "addlayer")
("Calc Trace Width" "twcal")
("Calc Via Quantity" "viacal")
("Cut Line" "clinecut")
("Cut Shape" "cutshape")
("Check width" "chgew")
("Etch Cross Check" "ecp")
(popup "Text Function") ;子選單名稱
("Edit TextBlock" "settxtpw")
("SilkScreen Export/inport" "text_out_in")
("Move Text2Center" "r2c")
("Check_NoRefdes" "ch_noref")
("Check_refdes_direction" "ch_dir")
("Check_text_grap" "ch_text_overlap")
(end)
(popup "SplitPlane")
("SplitPlane_CreateLayers" "SplitPlane_CreateLayers")
("SplitPlane_CreateShapes" "SplitPlane_CreateShapes")
(end)
(popup "DataBase Check")
("DataBase &Check..." "dbdoctor")
("DANGLING CHECK" "dangling")
("DumpVia CHECK" "check_dvia")
(end)
(popup "TAPEOUT")
("Artwork..." "artwork")
(separator)
(popup "AUTO DRILL")
("SET NCcustom" "setnccus")
("Drill Legend" "nclegend")
("Drill Route" "ncdr")
(end)
("Setting FilmControl" "efilm")
("Auto CreateArtWork" "ns_gerber")
("Output GFile" "outfilm")
("draw pin hole" "draw pin hole")
("Ouput DXF/RefPdf/IPC356" "odxf")
("Ouput SymLoc" "inform")
(popup "Sort Output File")
("Move Gfile" "sortgfile")
("Zip Gerber" "gzip")
(end)
(end)
("Export CAD" "cadout")
(separator)
(popup "[ System Tools ]")
("[ Snap Screen ]" "system snippingtool")
("[ Run Notepad ]" "system notepad")
("[ Run Calculator ]" "system calc")
("[ Run Paint ]" "system mspaint")
("[ Run CMD ]" "system")
(end)
(end)
)
)
(t
;這裡是擺放英文位置
lSkillMenu = '(
(popup "EDA365 Skill for Test") ;主選單上的名稱
("Chinese Transfer" "(fnChineseTransform)") ;第一個字串是顯示在選單上,第二個字串是執行命令
("Quick Open" "filemgr") ;程式選單項目
(separator) ;區格線
("Netin,3rd Party" "netin3rd_protel")
("Compare Net_Changes" "gnetrpt")
("Compare BRD_Changes" "component_changes")
("Clear Layout TempFile" "tmpdel")
("Check Height" "heightchk")
("Hilight TestPoint Net" "hlnpt")
("Set_drillkey" "setdrill")
("Set Design Color" "s1")
("Show Height/width" "draw targets")
("Add Layer" "addlayer")
("Calc Trace Width" "twcal")
("Calc Via Quantity" "viacal")
("Cut Line" "clinecut")
("Cut Shape" "cutshape")
("Check width" "chgew")
("Etch Cross Check" "ecp")
(popup "Text Function") ;子選單名稱
("Edit TextBlock" "settxtpw")
("SilkScreen Export/inport" "text_out_in")
("Move Text2Center" "r2c")
("Check_NoRefdes" "ch_noref")
("Check_refdes_direction" "ch_dir")
("Check_text_grap" "ch_text_overlap")
(end)
(popup "SplitPlane")
("SplitPlane_CreateLayers" "SplitPlane_CreateLayers")
("SplitPlane_CreateShapes" "SplitPlane_CreateShapes")
(end)
(popup "DataBase Check")
("DataBase &Check..." "dbdoctor")
("DANGLING CHECK" "dangling")
("DumpVia CHECK" "check_dvia")
(end)
(popup "TAPEOUT")
("Artwork..." "artwork")
(separator)
(popup "AUTO DRILL")
("SET NCcustom" "setnccus")
("Drill Legend" "nclegend")
("Drill Route" "ncdr")
(end)
("Setting FilmControl" "efilm")
("Auto CreateArtWork" "ns_gerber")
("Output GFile" "outfilm")
("draw pin hole" "draw pin hole")
("Ouput DXF/RefPdf/IPC356" "odxf")
("Ouput SymLoc" "inform")
(popup "Sort Output File")
("Move Gfile" "sortgfile")
("Zip Gerber" "gzip")
(end)
(end)
("Export CAD" "cadout")
(separator)
(popup "[ System Tools ]")
("[ Snap Screen ]" "system snippingtool")
("[ Run Notepad ]" "system notepad")
("[ Run Calculator ]" "system calc")
("[ Run Paint ]" "system mspaint")
("[ Run CMD ]" "system")
(end)
(end)
)
)
)
procedure(fnDynamicMenusTrig(tMenuFile)
let((xMenuID)
when(tMenuFile == "allegro" ;只判斷第一次載入及執行,如果沒有此判斷的話,有其他程式也是使用動態選單時,就會再加載一次
xMenuID = axlUIMenuFind(nil -1)
axlUIMenuInsert(xMenuID lSkillMenu)
)
)
)
procedure(fnChineseTransform() ;中文碼轉八進位的ASCII碼函數
axlUIPrompt("Code:",sprintf(nil,"%L",axlUIPrompt("Please Input Chinese:")))
)
; Using the trigger function directly
axlTriggerSet('menu 'fnDynamicMenusTrig)

复制代码

XYX365 · 发表于 2016-1-28 18:47

361553894 发表于 2016-1-28 13:14
15版本的菜单插入就不提供了

再確認一下,你的程式功能,
1.在Allegro.ilinit裡面加載 SkillMenu.il
2.開啟Allegro.exe
3.執行sm
4.這時候就加載你所設定的Menu(m1~m7),之後會重覆加載好幾次

這是因為下面的判斷問題
when(g_SkillMenuTimerNum>1
if(isCallable('axlUIMenuFind) then
if(axlUIMenuFind(nil,"wxGrids") then
axlUIWTimerRemove(g_SkillMenuTimerId)
g_SkillMenuTimerId='unbound
g_SkillMenuTimerNum='unbound
return(t);
);if
);if
);when

你的程式工作流程應該是這樣
1.執行sm後,
2.執行下列
   g_SkillMenuTimerId=nil
   g_SkillMenuTimerNum=0
   g_SkillMenuTimerId=axlUIWTimerAdd(nil,2000,nil,'wxSkillMenu_TimerCallBack)

3.時間等待2000後再執行wxSkillMenu()函數,
4.這時候就執行下面並執行好幾次
when(g_SkillMenuTimerNum>1
if(isCallable('axlUIMenuFind) then
if(axlUIMenuFind(nil,"wxGrids") then
axlUIWTimerRemove(g_SkillMenuTimerId)
g_SkillMenuTimerId='unbound
g_SkillMenuTimerNum='unbound
return(t);
);if
);if
);when

如果你只要加載一次的話,你修改成下面試試看,只留紅字部分
   if(boundp('g_SkillMenuTimerId) && boundp('g_SkillMenuTimerNum) then
;if(g_SkillMenuTimerNum>5 then
; axlUIWTimerRemove(g_SkillMenuTimerId)
; g_SkillMenuTimerId='unbound
; g_SkillMenuTimerNum='unbound
;else
; g_SkillMenuTimerNum++
;);if
;when(g_SkillMenuTimerNum>1
; if(isCallable('axlUIMenuFind) then
; if(axlUIMenuFind(nil,"wxGrids") then
axlUIWTimerRemove(g_SkillMenuTimerId)
         g_SkillMenuTimerId='unbound
g_SkillMenuTimerNum='unbound
return(t);
; );if
; );if
;);when
else

g_SkillMenuTimerId=nil
g_SkillMenuTimerNum=0
g_SkillMenuTimerId=axlUIWTimerAdd(nil,2000,nil,'wxSkillMenu_TimerCallBack)
);if

361553894 · 发表于 2016-1-29 09:19

XYX365 发表于 2016-1-28 19:02
其實不用加入你貼的程式,也可以加載一次,就不會重覆好幾次,我猜原始作者應該有遇到過加載第一次失敗的問 ...

Skill > axlTriggerPrint
E- *Error* skillDev not enabled.
E-
ERROR
Skill > axlTriggerPrint()
E- *Error* skillDev not enabled.
E-
ERROR
Skill >
这个是什么原因呢？

361553894 · 发表于 2016-1-29 08:41

XYX365 发表于 2016-1-28 19:02
其實不用加入你貼的程式,也可以加載一次,就不會重覆好幾次,我猜原始作者應該有遇到過加載第一次失敗的問 ...

我之前有试过，只加载一次，发现会被刷掉，估计他其他的函数跟菜单加载有冲突
他这个目的是不是隔两秒检查一次菜单有没有存在，如果存在就跳出，否则就重新加载

蓝色的天口 · 发表于 2017-8-28 16:14

太难了，看不懂如有有大神录视频就好了

hyper311 · 发表于 2017-8-27 17:04

好强大

mentorkk · 发表于 2016-11-13 13:47

謝謝樓主分享

hy20060614 · 发表于 2016-11-11 15:01

谢谢分享

mistletoe · 发表于 2016-2-22 14:08

非常不错，download 学习下

TobyTao_Zhang · 发表于 2016-2-19 16:09

謝謝大大的分享,
学习一下！

yaoshasha · 发表于 2016-2-19 14:44

谢谢分享

XYX365 · 发表于 2016-2-19 11:17

shihongjing 发表于 2016-2-19 10:00
请问一下怎么才能让菜单出来，我加载了没有反应，command里显示 loading axlcore.cxt t

你直接將此行 load("fDynamicMenus.il") 加入到allegro.ilinit,然後開啟allegro.exe就會自動加載

shihongjing · 发表于 2016-2-19 10:00

请问一下怎么才能让菜单出来，我加载了没有反应，command里显示 loading axlcore.cxt t

JIMDENG · 发表于 2016-2-17 16:06

学习一下！

shihongjing · 发表于 2016-2-16 15:25

请问一下怎么才能让菜单出来，我加载了没有反应，command里显示
loading axlcore.cxt
t

shihongjing · 发表于 2016-2-16 15:16

正需要这个东西呢，谢谢。

卫冬冬 · 发表于 2016-2-9 15:31

学习学习了解了解

nanosoc · 发表于 2016-1-29 22:05

谢谢分享

		自动登录	找回密码
密码			注册

【分享源代碼】建立動態選單/添加自定义菜单

本帖子中包含更多资源

点评

推荐内容 /1