|
|
本帖最后由 huangyi54321 于 2011-10-7 03:59 编辑
9 o# [$ K1 s# R0 w- H' E) f) a% ~3 x: A* s* S
按照帮助里面的说明操作，在Allegro输入命令时出错（如图）
$ ^" c6 X7 ~ x! H' J& ^) k不知道哪里的问题？
6 k6 Z2 @+ }% W: m8 B4 N
0 R/ M7 q" }/ d! a$ k0 T" c5 M
Procedure 1— PADS and Allegro on the Same Machin
# t3 B& D3 _; w# N- h* jPerform the following steps to migrate an Allegro design to PADS Layout when PADS Layout and Allegro PCB Editor reside on the same machine:7 n% X! k" L% I0 L
1. Prepare the Allegro design(s) for migration, as follows: ; k |: w j7 O2 O' p
a. Copy the contents of the <PADS install dir>\SDD_HOME\translators\skill_scripts folder to the $HOME\pcbenv folder. 0 E( [( ~! v5 w8 x0 ?% j+ n
b. Foreach design you want to translate:
" ?) [4 r$ i+ E b6 Q& li. Create a new folder(...myboards_<boardID>), for example), and copy into it the Allegro design (.brd) file you want to migrate.
7 P* Z: s" j* f6 G2 sii. Open the design file, and in the Allegro command prompt window enter these command lines:
: r, q8 g9 d$ S2 e5 f$ RCommand> skill load “dfl_main” (include quotes)8 z+ j2 l( s: \1 J: W
Command> main out ( Y% B$ D w2 F0 [4 t" K6 D! c3 x; }
iii. In the Allegro to Expedition Translator dialog box, click the Start One Way Translation button. 5 y0 O. o0 s% q
iv. When the SKILL script has completed, if any errors were found, fix them and rerun the SKILL script. The migration will not complete correctly if all errors are not fixed.
' l, h1 O7 c9 B+ I2. Migrate the prepared Allegro design(s) to PADS Layout.
: L6 v6 ~ D4 `- ATip: If you're migrating only a single design including attributes, use the File > Import command in PADS Layout instead of the following procedure. After the design is migrated, it is automatically opened in PADS Layout. If you are migrating multiple designs, or want to choose whether to translate attributes or not, perform the following steps:
/ n4 t9 w$ D' M. M3 X* na. From the Start Menu, run the Allegro to PADS Translator. " e; b7 m" M h L! K, E- i* X# j8 M" g
b. In the Allegro Designs Translator dialog box:
2 f z4 \' r$ C# Hi. Identify the location where you want the translated files placed. " E8 ^& i! ]! M G- S" u
ii. Use the Add button to specify the files you want to translate.
- l7 G& e8 P4 F5 U U1 Hiii. Specify whether or not to translate attributes.
; m+ V% p8 V' ^0 c% o7 Civ. Click the Translate button. The output filename(s) will be in the format
) K0 ^' Q9 a! Q. ^' ~# c/ \
) S( O0 i% p0 j( Sdesign_##########.pcb.
! M: q; y1 C' n; c/ w+ e |
|
/1 
发表于 2011-8-5 08:19
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
支持！
反对！
