标题: IBIS在Mode Integrity中出现了如下错误 [打印本页] 作者: xiaochaoaction 时间: 2012-7-21 11:01 标题: IBIS在Mode Integrity中出现了如下错误 WARNING (line 433) - Pulldown Maximum data is non-monotonic0 s2 G- v* w& C
WARNING (line 434) - Pulldown Typical data is non-monotonic ' E" a$ g- r, @9 ?! yWARNING (line 435) - Pulldown Minimum data is non-monotonic % z) s* g& Q5 u" }4 Z1 j& rWARNING (line 609) - Pullup Maximum data is non-monotonic5 W2 d6 r1 q, ]
WARNING (line 610) - Pullup Typical data is non-monotonic 5 f$ r+ ~ C5 D( i2 e9 |: mWARNING (line 610) - Pullup Minimum data is non-monotonic4 M" O- t5 o$ e: u& X0 \
WARNING (line 1028) - Pulldown Maximum data is non-monotonic ( V- u. f7 i2 Y( ^( s9 V) Q/ wWARNING (line 1029) - Pulldown Typical data is non-monotonic% u0 o# _' i/ X, D
WARNING (line 1030) - Pulldown Minimum data is non-monotonic1 c" \& F0 k( G, _ r
WARNING (line 1535) - Pulldown Maximum data is non-monotonic4 p% j8 k" f4 ^
WARNING (line 1536) - Pulldown Typical data is non-monotonic% L# {& l; I. @- v8 |& @6 C
WARNING (line 1537) - Pulldown Minimum data is non-monotonic# A0 a: [/ B- F, Y
WARNING (line 1717) - GND Clamp Minimum data is non-monotonic- Z0 `: t$ r) Q
WARNING (line 1890) - POWER Clamp Minimum data is non-monotonic7 z7 [; x: \) n7 q) f( L' q, H: U
WARNING - Model 'DBX_B06060B0S2AKZGBE': Vmeas timing test load parameter should be specified# g1 \% g6 Z5 [2 \& k
WARNING (line 1944) - Pulldown Maximum data is non-monotonic1 W) z: ?8 r% e
WARNING (line 1945) - Pulldown Typical data is non-monotonic3 h- }" }: B4 s+ a5 V H3 X
WARNING (line 1946) - Pulldown Minimum data is non-monotonic* M& u4 L$ e) N5 w2 [
WARNING (line 2153) - Pullup Maximum data is non-monotonic" D5 x6 w' I0 E1 H) U
WARNING (line 2154) - Pullup Typical data is non-monotonic" V4 g' E' r( I* V, t3 C0 Q2 S4 a
WARNING (line 2154) - Pullup Minimum data is non-monotonic9 E3 n1 | v/ u1 o' k! w; t8 M
WARNING - Model 'DBX_B08081B0S2ALZGIE': Vmeas timing test load parameter should be specified * k7 a1 S- W/ v5 RWARNING - [Model] DBX_D00200B0S2AZZGHE has no description of the buffer's high state; J4 U: Z! S3 s( n* O+ |
DC drive characteristics (no [Pullup] table). This warning 8 k. D' J1 i* u% u- q can be silenced by using an open drain Model_type or by: N2 Z+ B- r5 Y/ J' m+ R: G/ p
adding a [Pullup] table. * h Y8 j% _1 t7 o8 n8 l $ ]" V# Z2 f# h谁能帮忙解决一下，谢了。。。作者: procomm1722 时间: 2012-7-24 22:10
這個不用理會作者: pwj6323 时间: 2012-7-28 11:08
无法修改。呵呵。。{:soso_e100:} 作者: yoyof3 时间: 2012-8-5 22:58
警告可以不管，把错误处理完就可以了。作者: xiaochaoaction 时间: 2012-8-11 16:25
