EDA365电子工程师网

标题: orcad Warning [ALG0015] rename问题 [打印本页]

作者: tangchanglong    时间: 2010-10-11 09:31
标题: orcad Warning [ALG0015] rename问题
#1 Warning [ALG0015] Net "UNNAMED_3_AM29LV320DB90EC_I943_OC" is renamed to "UNNAMED_3_AM29LV320DB90EC_I943_".4 \- P1 b) v7 H7 E: J
#2 Warning [ALG0015] Net "UNNAMED_5_CONRJ45UNSHLD_I295_PIN7" is renamed to "UNNAMED_5_CONRJ45UNSHLD_I295_PI".
4 Y- q  G  n$ K( Z" S#3 Warning [ALG0015] Net "UNNAMED_5_CONRJ45X4UNSHLD_I294_PIN6" is renamed to "UNNAMED_5_CONRJ45X4UNSHLD_I294_".
8 v; |# R; B: H+ f6 l#4 Warning [ALG0015] Net "UNNAMED_5_CONRJ45X4UNSHLD_I294_PIN1" is renamed to "UNNAMED_5_CONRJ45X4UNSHLD_I29_1".3 a& |. O1 _7 X' v
#5 Warning [ALG0015] Net "UNNAMED_5_CONRJ45X4UNSHLD_I294_PIN12" is renamed to "UNNAMED_5_CONRJ45X4UNSHLD_I29_2".  F9 ~* M/ g7 E" t0 L" q
#6 Warning [ALG0015] Net "UNNAMED_5_CONRJ45X4UNSHLD_I294_PIN22" is renamed to "UNNAMED_5_CONRJ45X4UNSHLD_I29_3".
, a% J: `/ s* ]) S4 |#7 Warning [ALG0015] Net "UNNAMED_5_CONRJ45X4UNSHLD_I294_PIN7" is renamed to "UNNAMED_5_CONRJ45X4UNSHLD_I29_4".
作者: tangchanglong    时间: 2010-10-11 09:43
标题: Value,Part,Footprint,NET,PIN NAME的长度设置
本帖最后由 tangchanglong 于 2010-10-11 10:00 编辑 6 S/ F  E6 e1 f7 B5 q# E; b6 O- C% L
2 e( o9 S3 i7 X5 a3 u: B1 j: E
因为Part Name 过长,自动截掉一部分。没有关系的7 y3 y; ]* ]& |( D: w" R
Warning是不影响生成网表的。如果是Error,就生成不了网表。
$ ~0 V3 o  @7 N2 B
! r3 t6 G7 T+ _6 l% F& t' H. S" r% r解决方法:
# x, O) P  v$ L3 l0 Z0 G更改Part Name 的长度,默认为31改为50(或更大值)
8 }; z+ m/ v; T: e  f8 p具体如下点击creat netlist,再点击pcb editor--setup,如下图
5 g6 Q/ h7 c" [8 W* }& a/ b. e) P3 ]
% F" l7 \  y- c' E2 ]' T
6 `) c3 D0 Y5 U( }9 M- W$ o! E; k4 f: T  [& F
Device/Net/PIN Name Char Limit的长度更改31为50(或其他更大值),ok
* q/ ?1 z3 g+ f! J3 M6 D0 Z5 x
作者: yxw0609131056    时间: 2011-1-5 21:51
哦,我也有同樣的疑問,謝謝了
作者: gxy198715    时间: 2011-10-28 10:10
小弟问一下,16.0到哪里去设置啊!因为在那里没有miscellaneous这项啊!
* u* {/ q  ~; ~5 u# f- t2 h
作者: 阁下你好    时间: 2011-10-31 14:10
我的没有上面的pcb editor,只有allegro,怎么调整呀!




欢迎光临 EDA365电子工程师网 (https://bbs.elecnest.cn/) Powered by Discuz! X3.2