求助Allegro16.2生成Artwork出现的问题

yjma

      跪求Allegro16.2生成artwork出现报错解决方法     ：


Results from parameter file ...
    DEVICE-TYPE           GERBER_RS274X
    OUTPUT-UNITS          INCHES
    FILM-SIZE             24000 16000
6 P' ~4 i! g+ B. r" h: F    FORMAT                5.3
    ABORT-ON-ERROR        NO
* W! ~0 b0 m" f1 D: @0 Z6 d3 Q    SCALE                 1
    SUPPRESS-LEAD-ZEROES  YES
    SUPPRESS-TRAIL-ZEROES NO
    SUPPRESS-EQUAL        YES
: Q- K) ^2 Y! w# |/ }# W2 K    UNDEF-APT-CONT        NO

$ Q1 X: a" b* l+ ^' Q: M WARNING: for raster artwork formats, artwork accuracy must be
  at least one place greater than the database accuracy, up
  to the maximum accuracy allowed by the selected output format.
6 U9 X! ]1 P+ D
  Increase the accuracy by increasing the "Decimal Places" in
  the FORMAT section of the artwork parameters and then rerun
4 W4 R% D' @/ V7 }2 E  artwork.

  The current output is rounding down the data.  Failure to change
  the format may result in inaccurate arc coordinates in the output
  files and possible shape/void plotting failures.
- _( o' Y* T+ J- C! T' @
3 E6 c8 N+ i8 c% \: J' r" {. p8 e
( a% w/ Y9 p! }% }0 ?================================================================
     PROCESSING FILM < POWER >
     TO FILE < E:/highvision/project/RK/RK3168/pcb/POWER.art > ...
================================================================
! @+ Z2 X% r* t  h; Q
  FILM PARAMETERS :
  ---------------------------------------------------------
# C# U9 C- [6 n$ `: G  Undefined line width                6.000
  Mirror code                         NONE
  Rotate angle                        NONE
2 N$ g  S/ a' Z  V; i  Offset x:                           0.000
  Offset y:                           0.000
  Plot negative                       NO
  Suppress unconnected internal pads  NO
; g( x+ {( v, }0 t+ T1 ~
( B7 \+ a% Y7 s0 X/ _2 z' e& [  k    WARNING: Film contains DRC error(s).
% b' q, f) V* U& u    WARNING: Segment with same start and end points at
        (312.890 -1452.988) will be ignored. Increasing output
        accuracy may allow segment to be generated.
2 g* b% Z0 A! S& p& i* w( c5 L
: n, Z9 P7 _4 p3 V2 ]    WARNING: Segment with same start and end points at
        (1074.500 -1458.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
, ?- N8 T5 R2 w6 ~8 ~4 [1 v
    WARNING: Segment with same start and end points at
        (-1203.819 -1693.181) will be ignored. Increasing output
- l6 w( o% ?- ]" M8 E$ u        accuracy may allow segment to be generated.
  c/ ^! V  c) c+ B% Q" @% e" H
9 p, D# |& r1 j# M0 ?    WARNING: Segment with same start and end points at
* H# W5 U- i4 T/ n6 _$ y* v        (-1128.882 -925.181) will be ignored. Increasing output
: I$ l" J/ H% w2 t/ S% O1 h        accuracy may allow segment to be generated.

    WARNING: Segment with same start and end points at
        (-1128.882 -903.642) will be ignored. Increasing output
        accuracy may allow segment to be generated.
! m, F, T! Y; Q+ q3 X  C3 n" ~
    WARNING: Segment with same start and end points at
        (-812.469 -725.142) will be ignored. Increasing output
" L3 r" E. V9 P$ ^# F        accuracy may allow segment to be generated.
+ X; ]: n+ A6 N) U6 K0 y$ e
9 b% O. T0 _" l    WARNING: Segment with same start and end points at
5 T+ B. `$ V$ `7 y! w        (-812.461 -725.059) will be ignored. Increasing output
        accuracy may allow segment to be generated.

    WARNING: Segment with same start and end points at
+ h, r, x' m' Y* ]4 s% j. }        (-768.260 -730.799) will be ignored. Increasing output
  a) f- H$ |5 }+ d" V3 `. J) w        accuracy may allow segment to be generated.

    WARNING: Segment with same start and end points at
9 Z  M3 D+ W! \. G) M0 }        (-943.358 -527.441) will be ignored. Increasing output
        accuracy may allow segment to be generated.
7 n% m3 k: i& j0 d: J, ?0 X
    WARNING: Segment with same start and end points at