Allegro导入第三方网表出错

656504257

本想把PADS Logic的转为ORCAD，下了个E-studio.pro软件安装不了，只好输出网表导入到Allegro，但是出现以下错误，请教高手，怎么解决？
^
ERROR(SPMHNI-63): Invalid keyword, keyword ignored.
9 j& ?$ ^% w  `% _+ d-------------------------------------------------------------------------------
: T0 f9 e5 I: M. C/ c* j0 v ^
Execution stopped before reading entire input file.
-------------------------------------------------------------------------------
  n/ K" W0 D5 e1 R
" V5 K: J4 B- D6 {2 G/ G! P6 S===========================================================
End of NETLIST IN Syntax/Logic Check
# A( A7 S: r( g* N3 D# P6 A. J===========================================================
& |- a; ?0 l" P, s$ w& }% H; Y
Total Netlist Warnings =  0.
Total Netlist Errors   =  1.


===========================================================
* T% J8 |1 ^. a2 I- S' @
( M( T- t0 s& @) B+ t% WTotal Device File Warnings =  0.
1 W- d$ ]% ~  h% c0 D6 K1 }  W  ~Total Device File Errors   =  0.

. B/ L6 b) s9 B% [7 Q" k% N===========================================================
! E" q3 e! A" ^5 g" V1 Z' [( j8 X8 N# I
Total Combined Netlist and Device File Warnings =  0.
Total Combined Netlist and Device File Errors   =  1.

===========================================================
( j  C; x$ V- \" W% K1 V. @: pEnd of Allegro NETLIST IN Log
8 {4 c, f! n/ Q* c( b0 c===========================================================

ayalcy

不行啊 ，还是报错
这个要怎么改啊

风吹摇摆

刚才说错了，这个要手动修改网表，在含有$$$的网络前面加上“$NETS”例如：
, a1 `( U' J$ q# F  x. K; I$NETS
% A4 b8 C! Z$ Y  ^* t. d'$$$883' ; NSR1.2 NSR2.2 U6.6
4 v5 l, e/ @* D* Y* m4 V' O'$$$1157' ; R438.2 U39.4
! ?9 T4 Z( k6 H4 H) U'$$$1184' ; R435.1 R439.2 U39.6
! `+ x0 p( x& Q) I5 g'$$$1196' ; R252.1 U31.2
) E' ^7 E$ g7 T$ o'$$$1198' ; R253.1 U31.1

3 D8 U# k& d, U1 h3 [1 u

风吹摇摆

查下网表里面有非法字符例如$$$883' ; NSR1.2 NSR2.2 U6.6
4 A" Q9 O; N9 g- T% ~4 o'$$$1157' ; R438.2 U39.4
'$$$1184' ; R435.1 R439.2 U39.6
'$$$1196' ; R252.1 U31.2
'$$$1198' ; R253.1 U31.1
'$$$1560' ; R49.1 U11.1
'$$$2732' ; R226.2 R229.2 U31.3
4 J2 E! ^2 K" [: V: O'$$$2826' ; R250.2 R254.2 U31.5
'$$$2903' ; R297.2 R298.2 U31.6
& |  Z! N7 b' F5 j0 _'$$$2954' ; C72.2 L6.1 Q24.5 Q24.6 Q24.7 Q24.8 R49.2
'$$$3044' ; R299.2 U31.7
'$$$4685' ; C177.1 C192.1 C196.1 L17.1 L31.1 U18.22
- O5 h: n3 W2 ]) \1 L! x( y8 Y# p'$$$4720' ; Q7.1 U11.2
'$$$4813' ; D6.1 L30.2 U9.1
'$$$5014' ; D2.2 J1.7 R269.2 R329.2
'$$$5015' ; D16.2 J1.5 R273.2
% \# U+ Y7 b( ?" `8 X3 M7 t. C'$$$5016' ; D3.2 J1.3 R276.2 R330.2
'$$$5017' ; D18.2 J1.2 R285.2 R331.2
'$$$5018' ; D20.2 J1.1 R264.2 R332.2
& \" Y2 y' J0 }1 G; F0 G4 i$ F'$$$5019' ; D1.2 J1.8 R286.2 R328.2
/ {6 g$ V6 d$ C8 P& |  Y'$$$5840' ; R122.1 U18.18
- T+ E8 X) O2 t4 X'$$$5842' ; R123.1 U18.19
0 x2 S; _- X5 Q. Y0 D'$$$5844' ; R124.1 U18.20
1 {" G' C5 n6 ]: g改过来就可以了

风吹摇摆

我的也是这样，总是有一个网络出错，在原理图里删除网络重新连后，另外一个网络出错了
求大神解决
，$$$883' ; NSR1.2 NSR2.2 U6.6
6 M% p% {3 W' Z4 j4 ^ ^
ERROR(SPMHNI-63): Invalid keyword, keyword ignored.
1 Z- Q& ~" H# P# X) _* p' b4 v/ K-------------------------------------------------------------------------------
/ I" T/ F; z4 @) m+ a# R' T ^
Execution stopped before reading entire input file.
8 U1 U0 A; I5 ?/ \-------------------------------------------------------------------------------
$ W, Y  b/ F# m* K5 |; c
===========================================================
6 @: i: `$ Z# p0 \& G" ~End of NETLIST IN Syntax/Logic Check
7 L( g8 ?0 H& ?  |- j1 N( r===========================================================

Total Netlist Warnings =  0.
1 W2 T9 W1 X8 U, \! _1 y  O0 r! PTotal Netlist Errors   =  1.