标题: Illegal net name [打印本页] 作者: tchming 时间: 2011-3-10 22:50 标题: Illegal net name 本帖最后由 tchming 于 2011-3-10 22:58 编辑 ! w5 Z9 l+ c4 j# i; ]( b9 ?2 i5 ^+ ]
4 x# |& x% ?+ f% F4 X请问版主orcad capture 16.3中测试管脚如何命名啊，我用testpin1、testpin2等3 i; F( V7 M# {" S3 U/ E6 C1 h
仿真时报错，具体如下：, W S8 C* M- y0 y% u
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN1.& K2 m7 Q) m3 Y9 V, A. P
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N00942., _0 }" n* t$ S3 r0 q
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N01010. |1 B4 N) l% d$ e0 i# NWARNING [NET0102] Illegal net name SIGNAL SOURCE1_N00942.# o z, _* R7 N2 q) j, ~
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN1.7 J) |, G3 V2 e" z/ G: N
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN2.+ m A+ |) S ^2 `
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N01010.5 ?, e( H. R7 H( v2 ?2 T
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_TESTPIN2. / k; U3 Z( _5 J2 t3 x2 yWARNING [NET0102] Illegal net name SIGNAL SOURCE1_N00942.; b( ^" F& l( U! s1 R% |
WARNING [NET0102] Illegal net name SIGNAL SOURCE1_N01010." M# H; n7 e3 P4 u3 l
WARNING [NET0102] Illegal net name 5-POLE SHAING1_N03569." n) Y' t& {% k( a
WARNING [NET0102] Illegal net name 5-POLE SHAING1_N03569.. q* ^% n1 z& t7 _: G7 s
WARNING [NET0102] Illegal net name 5-POLE SHAING1_N03569." V% t, n; A4 U1 O2 B
WARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_A275 NO_2_N00953.) U$ o! ?2 A3 c3 }3 d, k
WARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_A275 NO_2_N00961. # K% O% ^, w5 g% ?% e! j5 P" Y0 |$ VWARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_A275 NO_2_N00953.! j' K/ g) q' d$ D& f
WARNING [NET0102] Illegal net name 5-POLE SHAING1_4-POLE SHAPING1_TESTPIN6.8 ^5 W- V+ U/ ^
1 H. G8 z; Z& J/ l) l
9 @9 r% u4 @4 j# k }0 N5 n2 a# V求指教6 B% ~' a& U6 F# H+ Y
" b5 W. F4 y% M/ F( P 作者: tchming 时间: 2011-3-11 16:29 回复 tchming 的帖子 3 n7 a* r! e2 J& k( m 2 {6 Q+ W) g9 y4 M原来是我用了一些没有Pspice模型的元件导致的 9 I; n ~3 s! B6 s