Allegro导入第三方网表出错

656504257 · 发表于 2013-4-9 17:58

EDA365欢迎您！

您需要登录才可以下载或查看，没有帐号？注册

x

本想把PADS Logic的转为ORCAD，下了个E-studio.pro软件安装不了，只好输出网表导入到Allegro，但是出现以下错误，请教高手，怎么解决？
^
ERROR(SPMHNI-63): Invalid keyword, keyword ignored.
-------------------------------------------------------------------------------
^
Execution stopped before reading entire input file.
-------------------------------------------------------------------------------

===========================================================
End of NETLIST IN Syntax/Logic Check
===========================================================

Total Netlist Warnings =  0.
Total Netlist Errors =  1.

===========================================================

Total Device File Warnings =  0.
Total Device File Errors =  0.

===========================================================

Total Combined Netlist and Device File Warnings =  0.
Total Combined Netlist and Device File Errors =  1.

===========================================================
End of Allegro NETLIST IN Log
===========================================================

风吹摇摆 · 发表于 2013-4-26 15:51

我的也是这样，总是有一个网络出错，在原理图里删除网络重新连后，另外一个网络出错了

求大神解决
，$$$883' ; NSR1.2 NSR2.2 U6.6
^
ERROR(SPMHNI-63): Invalid keyword, keyword ignored.
-------------------------------------------------------------------------------
^
Execution stopped before reading entire input file.
-------------------------------------------------------------------------------

===========================================================
End of NETLIST IN Syntax/Logic Check
===========================================================

Total Netlist Warnings = 0.
Total Netlist Errors = 1.

风吹摇摆 · 发表于 2013-4-26 16:06

查下网表里面有非法字符例如$$$883' ; NSR1.2 NSR2.2 U6.6
'$$$1157' ; R438.2 U39.4
'$$$1184' ; R435.1 R439.2 U39.6
'$$$1196' ; R252.1 U31.2
'$$$1198' ; R253.1 U31.1
'$$$1560' ; R49.1 U11.1
'$$$2732' ; R226.2 R229.2 U31.3
'$$$2826' ; R250.2 R254.2 U31.5
'$$$2903' ; R297.2 R298.2 U31.6
'$$$2954' ; C72.2 L6.1 Q24.5 Q24.6 Q24.7 Q24.8 R49.2
'$$$3044' ; R299.2 U31.7
'$$$4685' ; C177.1 C192.1 C196.1 L17.1 L31.1 U18.22
'$$$4720' ; Q7.1 U11.2
'$$$4813' ; D6.1 L30.2 U9.1
'$$$5014' ; D2.2 J1.7 R269.2 R329.2
'$$$5015' ; D16.2 J1.5 R273.2
'$$$5016' ; D3.2 J1.3 R276.2 R330.2
'$$$5017' ; D18.2 J1.2 R285.2 R331.2
'$$$5018' ; D20.2 J1.1 R264.2 R332.2
'$$$5019' ; D1.2 J1.8 R286.2 R328.2
'$$$5840' ; R122.1 U18.18
'$$$5842' ; R123.1 U18.19
'$$$5844' ; R124.1 U18.20
改过来就可以了

风吹摇摆 · 发表于 2013-4-26 16:25

刚才说错了，这个要手动修改网表，在含有$$$的网络前面加上“$NETS”例如：
$NETS
'$$$883' ; NSR1.2 NSR2.2 U6.6
'$$$1157' ; R438.2 U39.4
'$$$1184' ; R435.1 R439.2 U39.6
'$$$1196' ; R252.1 U31.2
'$$$1198' ; R253.1 U31.1

ayalcy · 发表于 2013-6-14 08:24

不行啊，还是报错
这个要怎么改啊

		自动登录	找回密码
密码			注册

Allegro导入第三方网表出错

EDA365欢迎您！

推荐内容 /1