|
|
EDA365欢迎您！
您需要 登录 才可以下载或查看，没有帐号？注册
x
Start AT91Bootstrap...
Init DDR... Done!
Loading 1-Wire info...
sn: 0x0; rev: 0x421
Downloading image...
chip id: 0xecda
Copy 0x50000 bytes from 0x40000 to 0x26f00000
Done!
U-Boot 2010.06 (Feb 25 2013 - 11:02:59)
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
macb0: No PHY present
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x200000, size 0x280000
2621440 bytes read: OK
## Booting kernel from Legacy Image at 22000000 ...
Image Name: Linux-2.6.39
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2411772 Bytes = 2.3 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39 (jakebo@dev-server-pc) (gcc version 4.2.0 20070413 (prerelease) (CodeSourcery Sourcery G++ Lite 2007q1-10)) #1 Tue Mar 19 16:19:08 CST 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Atmel AT91SAM9X5-EK
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: mem=128M console=ttyS0,115200 mtdparts=atmel_nand:8M(bootstrap/uboot/kernel)ro,-(rootfs) root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 124820k/124820k available, 6252k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff000000 - 0xffe00000 ( 14 MB)
vmalloc : 0xc8800000 - 0xfee00000 ( 870 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002b000 ( 140 kB)
.text : 0xc002b000 - 0xc04aeac4 (4623 kB)
.data : 0xc04b0000 - 0xc04e0f60 ( 196 kB)
NR_IRQS:192
AT91: 128 gpio irqs in 4 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
AT91: CM rev B and higher
AT91: EK rev B and higher
AT91: Power Management (with slow clock mode)
AT91: Starting after power-restored wakeup
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 62 (SDA) and 63 (SCL)
at_hdmac at_hdmac.0: Atmel AHB DMA Controller ( cpy slave ), 8 channels
RomBOOT
请问大家有遇到过此问题吗？我量过复位引脚和电源，都没有问题。
|
|
/1 
发表于 2015-4-21 18:20
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
支持！
反对！
发表于 2015-8-31 16:31