原理图与封装引脚编号对应问题

GoPo

我画了一个BGA100的封装，在原理图中，字母是从Ａ～Ｊ。用向导画出来的封装字母从Ａ～Ｋ，没有Ｉ，导入网表的时候就会产生引脚编号不匹配的错误。

请问能不能很方便地改封装中的引脚编号？
7 E) E! a! _  _9 R- J$ _
- a# w7 s# F& F: T4 @4 m错误信息如下：
#2   ERROR(305) Device/Symbol check error detected.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K1'.
* O# m9 x. {" o. t! ~Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K2'.
  S3 ?7 ^* P6 L( g- uSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K3'.
0 z, v$ B+ L) D7 M5 A  l$ t; h" [1 \Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K4'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K5'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K6'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K7'.
) Y: T& S8 \! g; [6 H+ I' hSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K8'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K9'.
& S- \7 V+ _5 D& b; j7 S1 l7 ^- P- J3 R& ESymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K10'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I2'.
1 f' `) d  h. s# f4 ?  VSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I3'.
/ M! f4 ~( n1 f/ o% CSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I6'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I5'.
# O6 s2 C! g1 {% @2 YSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I1'.
" T2 \0 m! h  ^% V2 n- mSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I4'.
6 Y+ \) z4 O9 |& G' R3 q9 PSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I7'.
) N- t& r1 w, ~% T9 j$ eSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I8'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I9'.
6 r' r  C2 D0 h  `! vSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I10'.

xiuzhong200402

我也明白了!

GoPo

原帖由 kxx27 于 2008-4-28 16:45 发表
I 在建BGA时是默认没有的，你不能将它改了。

& ?. J& f8 y" ~% n1 r
& C8 [& A* }6 @$ d- o8 s+ b经过一番摸索，我解决了。用edit->text，点选J，在命令里输Ｉ就可以把它改成Ｉ了。把所有的都改过来之后错误就没了

panhaojie

学习了

gino

我也去建个ＢＧＡ　试哈