标题: 光绘出问题了！！！！ [打印本页] 作者: buptdlmuzbx 时间: 2011-4-20 16:30 标题: 光绘出问题了！！！！ 本帖最后由 buptdlmuzbx 于 2011-4-20 16:45 编辑 A8 M+ |# l7 r! b ' y1 t' ^/ W6 }) O$ c1 v( [4 R6 ~SUMMARY: 9 a: j0 ~6 i3 V5 w5 s TOP created with warnings & k9 Q* C# W. U5 o4 u+ ` GND created with warnings: y: y& ^4 ]3 ~1 i
VCC created with warnings ! G7 J' \8 p5 v9 r7 `7 ?; R BOTTOM created.; @ k) N/ j1 ]. m+ j+ D% f% F
SILKSCREEN_TOP created with warnings1 m n8 J# X4 e3 f; ?9 G
SILKSCREEN_BOTTOM created.2 E, A8 J @( k* N( @
SOLDERMASK_TOP created.6 _& \; z4 @) r" X9 M4 }
SOLDERMASK_BOTTOM created., N" O } o: s- n r
PASTEMASK_TOP created.5 X, A0 k( z9 d H. x- G
PASTEMASK_BOTTOM created. % R7 }" |; j5 W# v OUTLINE created. 5 ?4 Z! L9 V" }' @0 L: N, O, U DRILL created. % Q1 C0 a. _8 o7 n @ ARTWORK finished8 U) n" o2 I# P7 I$ e/ g6 r
这是最后的结果，. Y+ _ u, ]" P! {5 |) l
我想问下既然光绘finished，那这些warning能忽略吗？ ! i. l1 U9 A6 r1 a/ }. ~7 {WARNING: 0 width line found at (0.0000 0.6350)1 i3 ]7 H# E% {4 K
... using undefined line width of 0.1524 1 H( `4 u# f* G) P: QWARNING: Multiple 0 width lines; all will be treated the same as the first.* j% B9 w# V v+ T; ]; S
... using undefined line width of 0.1524 4 x6 p- N8 m. E WARNING: No Photoplot Outline was found,# b h3 x+ V$ Q+ Z* {/ A% H( B
negative shape outline will be determined by Board Outline& s4 l4 x7 N: J, a
WARNING: No Photoplot Outline was found, h& R9 ?$ ~: ?negative shape outline will be determined by Board Outline/ d. m ~ c2 }* l; s7 g
WARNING: text composed 0 width line found at (9.7282 5.5626). ?# U: |& i9 m6 K4 W
... using undefined line width of 0.15242 G% W |8 ?0 ?9 D# |7 W
WARNING: text having Multiple 0 width lines; all will be treated the same as the first. 8 M# O; ?1 }( M7 {: m6 {5 R* t( k8 J ... using undefined line width of 0.1524 9 k- r0 F% F6 E: f8 [( q2 l2 U2 u" d" }( t$ k' v9 e8 O# `
" c) ~5 u/ d3 c8 U这是什么呀！谁能给解决下！有木有！有木有！ 1 Z# ~) u/ j, D' n8 N作者: penny190 时间: 2011-4-20 16:42 請問您是不是有SHAPE做的零件超出板框了呢？作者: neg 时间: 2011-4-20 21:48
artwork中将每层的undefined line width不要设置为零作者: leavic 时间: 2011-4-20 22:27
可以，我经常碰到这种未定义线宽的warning，只要自己定义了undefiend line width就可以。/ I; N! M) ?, T& N& \: |
奇怪的是有些板子会报这种warning，有些就完全不会，虽然都有未定义线宽的trace。
請問您是不是有SHAPE做的零件超出板框了呢？