EDA365电子工程师网
标题:
orcad library builder 16.6.62创建PCBfootprint库导出后没管焊盘管脚？
[打印本页]
作者:
ylgw811002
时间:
2018-3-4 23:53
标题:
orcad library builder 16.6.62创建PCBfootprint库导出后没管焊盘管脚？
在创建PCB footprint库导出时，没有焊盘不知道什么原因？如图所示，并出现下面提示：E- (SPMHAP-2): No padstack specified.E- (SPMHAP-3): Problem loading 'c45.pad'.
; [; f) \- T! ~# \% F! @
; e2 |5 f& A U7 h0 I0 R9 C9 e% V. d
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
+ e. t$ Q& T( [; U( B
E- (SPMHAP-2): No padstack specified.
4 A) [6 B5 @6 ~& o, J0 r% D
- F$ i0 ]# ?9 L, n& W
E- (SPMHAP-3): Problem loading 'c45.pad'.
: |7 l' m) @9 ]' K
3 n9 d+ f5 B6 z# c
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
0 _( }+ ?! D# v( {, g
E- (SPMHAP-2): No padstack specified.
2 p3 \5 F$ c$ f" u+ I1 V
0 D% v- F/ F) \: y8 J
E- (SPMHAP-3): Problem loading 'c45.pad'.
1 B) l# ~! d% X E& V2 O
$ B9 Y( T; G5 L
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
8 w/ I$ p2 s! f" f I4 E
5 n$ q& B3 Y3 N0 b8 X; x
E- (SPMHAP-2): No padstack specified.
! y3 Z/ p( v. P* A
+ k* z1 x* G$ ^9 h; d9 Z+ O# y
E- (SPMHAP-3): Problem loading 'c45.pad'.
+ k5 B: [8 `+ y# _" `
; z9 M) k3 ? n+ j0 t
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
0 @4 P; }- y: I9 `- X
E- (SPMHAP-2): No padstack specified.
1 n/ b, r. c$ B9 y1 A7 E2 }7 x
4 W) V' U7 J6 X4 @% K8 c& A+ |
E- (SPMHAP-3): Problem loading 'c45.pad'.
' ^5 `* E; k, Q2 O3 M1 }! {
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
9 C$ x% y# Z$ Z' _2 x
& c8 b5 {$ C; I; N7 |" }# z. F8 e
E- (SPMHAP-2): No padstack specified.
9 Y8 r5 K6 U# A2 _# F
. O' h) b# E+ H8 T/ B3 i) U4 |* O$ j ~
E- (SPMHAP-3): Problem loading 'c45.pad'.
: F7 H8 C6 t2 ?6 u3 Q5 i7 W
3 P! Y. f% r0 E0 f
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
; S2 _5 t8 ^1 F4 I P2 I2 e) O
* _. R) ?5 x w9 R& r
E- (SPMHAP-2): No padstack specified.
! W+ r! j/ e! b- [& b
. g) C; F9 G% Y% y
E- (SPMHAP-3): Problem loading 'c45.pad'.
* p) ]! r* U. z2 x( k1 H
# V& [& m8 R/ x* e$ V- f" U
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
+ E* _0 t1 @# @0 q
作者:
ylgw811002
时间:
2018-3-5 00:10
2 、在allegro中，软件默认的焊盘那些路径不能删除。即padpath路径下的$padpath不能给删除；出现此问题只和padpath路径有关系，和psmpath路径没有关系，路径设置如下（可以在原来的基础上添加其它路径）： 1
: S/ s9 y$ w( s3 E
作者:
yangjinxing521
时间:
2018-3-5 08:46
正解
作者:
TobyTao_Zhang
时间:
2018-3-5 11:08
export libraries 之前先把要导出到 的folder 路径也加到padpath 里面
作者:
ylgw811002
时间:
2018-3-5 21:12
为啥通孔类的没有焊盘了 擦 能否给个详细的教程
作者:
ylgw811002
时间:
2018-3-6 16:46
能不能自动 DB doctor 生成的焊盘总是有问题
作者:
ylgw811002
时间:
2018-3-14 22:50
能有大神给个解决的办法了 多谢了
作者:
liangping367
时间:
2018-3-16 22:33
你能够导出OLB文件吗
; i; B, v* }5 Z$ k
欢迎光临 EDA365电子工程师网 (http://bbs.elecnest.cn/)
Powered by Discuz! X3.2
